Homework Answers
Add Answer to:
Given: y Тр Cross Section 14 in 2.5 in 18 in The circular steel rod shown...
1. A steel bar with solid circular cross section has a diameter d= 2.5 in., a...
1. A steel bar with solid circular cross section has a diameter d= 2.5 in., a length L = 60 in. and a shear modulus of elasticity G = 1 1.5 × 106 psi. The bar is subjected to torque T- 350 lb-ft as shown. (a) Find the angle of twist between the d 2.5 in (b) Find the maximum shear stress in the (c) Find the shear stress ta at a distance (d) Find the shear stress Tcenter at...
1. The part shown consists of a bent rod with a solid circular cross section of...
1. The part shown consists of a bent rod with a solid circular cross section of diameter 20 mm. Consider the cross- section on a cut at both a-a, and b-b. 400 mm A] For each cut, label the shear force, bending moments, and torsion moments. Then determine the critical point with the highest normal stress at each cross- section. No stress calculations are required. /100 mm 1 BJ Determine the point of highest normal stress for the bent rod...
df 1n mon diame ss: F size 0.70 V): A cold drawn C-1025 steel rod of circular cross section is subjected to a variable bending moment of 10,000 in-lb to 17,000 in-lb, as the axial load varies fro...
df 1n mon diame ss: F size 0.70 V): A cold drawn C-1025 steel rod of circular cross section is subjected to a variable bending moment of 10,000 in-lb to 17,000 in-lb, as the axial load varies from-2,000 lb to 5,000 lb. The maximum bending moment occurs at the same instant that the axial load is maximum. Determine the required diameter of the rod for a factor of safety N-2.3? The steel rod is connected to the support which causes...
15 Section 5, Problem 15 (25 pts.). A member is loaded by forces a, cand d...
15 Section 5, Problem 15 (25 pts.). A member is loaded by forces a, cand d as shown. The member is a hollow member with an outer radius of ro and a wall thickness of t. The member is fixed at ground level where points Fand G occur. Determine: a) the normal and shear stress at point F. b) the normal and shear stress point 02:46:29 Forces: a = 30 (k),c=16 (k), and -17 (K) Dimensions: e = 32 (in.),...
A beam is loaded by a shear force V. The beam cross-section is shown below. The...
A beam is loaded by a shear force V. The beam cross-section is
shown below. The moment of inertia of the cross-section is 347.1
in4. The centroid of the cross-section is 6.25 inches
from the base. Determine:
a) the shear stress at point A.
b) the shear stress at point B.
c) the maximum shear stress in the cross-section.
V = 50 (kips)
The maximum shear stress at point A is _____(ksi)
The maximum shear stress at point B is...
The dimensions for the W 21x62 beam cross section (shown below) are in inches: tf =...
The dimensions for the W 21x62 beam cross section (shown below)
are in inches: tf = .615, tw = .4,
bf = 8.24, d = 21. What is the maximum transverse shear
stress on the beam cross section if the shear force acting on it is
5.2 kip?
0.706 ksi
0.25 ksi
0.365 ksi
1.023 ksi
Point E у tw 15 kips 1 bf Point F
For the beam and loading shown, determine: A. The maximum shearing force in the beam =...
For the beam and loading shown, determine:
A. The maximum shearing force in the beam = kips
B. The maximum bending moment in the beam = kip in
C. The centroid of the cross section is at (in.) from the bottom
b
D. The moment of inertia of the cross section = in^4
E.the shearing stress at point a = ksi
F. The shearing stress at point b = ksi
G. The max shearing stress in the cross section =...
Prob #4: The Mohr circle associated with x-y state of stress on a component is shown...
Prob #4: The Mohr circle associated with x-y state of stress on a component is shown below (not necessarily to scale). 5.0 28p D(si) 20 Tiksi) 61 ksi Component Yield Stress in magnitude on planes whose The component is subjected to shear stress of ~ normal is along x or y directions A)2.8 B)56C)6.1 D) 8 E)10 F)12.2 ks G)18.3 G)3.7 14. H)20 l)24.4 )26.2 - 15. Based on the Max. Principal Stress Theory, the factor of safety for yielding...
A flanged cross section is used to support the loads shown in Figure 5. The dimensions...
A flanged cross section is used to support the loads shown in Figure 5. The dimensions of the cross section are given in a figure below. Consider the entire 20-ft length of the beam and determine: (a) Draw diagrams of shear forces and moments, (b) Determine maximum tensile normal stress in the cross section, and (c) Determine maximum compression normal stress in the cross section. 700 lb 1,500 lb 4 in. 1 in. 200 lb/ft in. B IC 12 in....
can someone help me with this strengths problem? A member is loaded by forces a, c...
can someone help me with this strengths problem?
A member is loaded by forces a, c and d as shown. The member is
a hollow member with an outer radius of r0 and a wall thickness of
t. The member is fixed at ground level where points F and G occur.
Determine:
a) the normal and shear stress at point F.
b) the normal and shear stress at point G
Forces;
a = 30 (k), c= 14 (k), and d...
1. A steel bar with solid circular cross section has a diameter d= 2.5 in., a length L = 60 in. and a shear modulus of elasticity G = 1 1.5 × 106 psi. The bar is subjected to torque T- 350 lb-ft as shown. (a) Find the angle of twist between the d 2.5 in (b) Find the maximum shear stress in the (c) Find the shear stress ta at a distance (d) Find the shear stress Tcenter at...
1. The part shown consists of a bent rod with a solid circular cross section of diameter 20 mm. Consider the cross- section on a cut at both a-a, and b-b. 400 mm A] For each cut, label the shear force, bending moments, and torsion moments. Then determine the critical point with the highest normal stress at each cross- section. No stress calculations are required. /100 mm 1 BJ Determine the point of highest normal stress for the bent rod...
df 1n mon diame ss: F size 0.70 V): A cold drawn C-1025 steel rod of circular cross section is subjected to a variable bending moment of 10,000 in-lb to 17,000 in-lb, as the axial load varies from-2,000 lb to 5,000 lb. The maximum bending moment occurs at the same instant that the axial load is maximum. Determine the required diameter of the rod for a factor of safety N-2.3? The steel rod is connected to the support which causes...
15 Section 5, Problem 15 (25 pts.). A member is loaded by forces a, cand d as shown. The member is a hollow member with an outer radius of ro and a wall thickness of t. The member is fixed at ground level where points Fand G occur. Determine: a) the normal and shear stress at point F. b) the normal and shear stress point 02:46:29 Forces: a = 30 (k),c=16 (k), and -17 (K) Dimensions: e = 32 (in.),...
A beam is loaded by a shear force V. The beam cross-section is
shown below. The moment of inertia of the cross-section is 347.1
in4. The centroid of the cross-section is 6.25 inches
from the base. Determine:
a) the shear stress at point A.
b) the shear stress at point B.
c) the maximum shear stress in the cross-section.
V = 50 (kips)
The maximum shear stress at point A is _____(ksi)
The maximum shear stress at point B is...
The dimensions for the W 21x62 beam cross section (shown below)
are in inches: tf = .615, tw = .4,
bf = 8.24, d = 21. What is the maximum transverse shear
stress on the beam cross section if the shear force acting on it is
5.2 kip?
0.706 ksi
0.25 ksi
0.365 ksi
1.023 ksi
Point E у tw 15 kips 1 bf Point F
For the beam and loading shown, determine:
A. The maximum shearing force in the beam = kips
B. The maximum bending moment in the beam = kip in
C. The centroid of the cross section is at (in.) from the bottom
b
D. The moment of inertia of the cross section = in^4
E.the shearing stress at point a = ksi
F. The shearing stress at point b = ksi
G. The max shearing stress in the cross section =...
Prob #4: The Mohr circle associated with x-y state of stress on a component is shown below (not necessarily to scale). 5.0 28p D(si) 20 Tiksi) 61 ksi Component Yield Stress in magnitude on planes whose The component is subjected to shear stress of ~ normal is along x or y directions A)2.8 B)56C)6.1 D) 8 E)10 F)12.2 ks G)18.3 G)3.7 14. H)20 l)24.4 )26.2 - 15. Based on the Max. Principal Stress Theory, the factor of safety for yielding...
A flanged cross section is used to support the loads shown in Figure 5. The dimensions of the cross section are given in a figure below. Consider the entire 20-ft length of the beam and determine: (a) Draw diagrams of shear forces and moments, (b) Determine maximum tensile normal stress in the cross section, and (c) Determine maximum compression normal stress in the cross section. 700 lb 1,500 lb 4 in. 1 in. 200 lb/ft in. B IC 12 in....
can someone help me with this strengths problem?
A member is loaded by forces a, c and d as shown. The member is
a hollow member with an outer radius of r0 and a wall thickness of
t. The member is fixed at ground level where points F and G occur.
Determine:
a) the normal and shear stress at point F.
b) the normal and shear stress at point G
Forces;
a = 30 (k), c= 14 (k), and d...
Most questions answered within 3 hours.
-
Select from the option list provided the most likely
classification(s) of net assets, if any, that...
asked 42 seconds ago -
Ivanhoe Corp. management is expecting a project to generate
after-tax income of $76,940 in each of...
asked 2 minutes ago -
An unknown compound contains only CC , HH , and OO . Combustion
of 5.30 g5.30...
asked 8 minutes ago -
List 3 viral classes based on their morphology.
What is the difference between lytic and lysogenic...
asked 10 minutes ago -
Myca Corp. has a project with the following cash flows. What is
the value of the...
asked 1 hour ago -
When an object moves through a fluid, the fluid exerts a viscous
force F on the...
asked 3 hours ago -
Why did the observed chemistry of thallium mislead Mendelev to
place the group 13 element (Tl)...
asked 4 hours ago -
A sine wave signal is displayed on the screen of an
oscilloscope. 6 peak-to-peak divisions are...
asked 7 hours ago -
a
1500 kg car accelerates from 0 to 25 m / s in 21.0s. How much...
asked 8 hours ago -
Calculate the molarity of each of the following solutions:
(a) 30.5 g of ethanol (C2H5OH) in...
asked 8 hours ago -
1 Refer to the build-borrow-or-buy framework as a decision tree
for the Adidas company. Identify a...
asked 8 hours ago -
Problem 2: The Problem of Social Cost. A Rancher and Farmer live
side-by-side to each other....
asked 9 hours ago