I have given a clear answer. Please upvote
it.
In the figure, the mass of the rigid rod Li is neglected while the beam L2...
Problem 4. A pivoted beam has mass mį suspended from one end and an Atwood's ma- chine suspended from the other with masses m2 and mz suspended on either side. The frictionless pulley has negligible mass and size. (a) Find the relation between mı, m2, m3, li, and l2 which will ensure that the beam has no tendency to rotate just after the masses are released. (b) What would you predict the relation would be in the case that all...
Problem 4. A pivoted beam has mass mį suspended from one end and an Atwood's ma- chine suspended from the other with masses m2 and mz suspended on either side. The frictionless pulley has negligible mass and size. (a) Find the relation between mı, m2, m3, li, and l2 which will ensure that the beam has no tendency to rotate just after the masses are released. (b) What would you predict the relation would be in the case that all...
For a mass-spring system shown in the figure below. Write the dynamic equations in matrix form and find the natural frequencies for this system, eigen values, eigen vectors and mode shapes assuming: m1=1 kg, m2=4 kg, k1=k3=10 N/m, and k2=2 N/m. / ر2 دی) x1(0) x2(0) K3 K1 W K2 mi W4 m2 (-?
Mechanical vibration subject
3. a. Consider the system of Figure 3. If C1 = C2 = C3 = 0, develops the equation of motion and predict the mass and stiffness matrices. Note that setting k3 = 0 in your solution should result in the stiffness matrix given by [ky + kz -k2 kz b. constructs the characteristics equation from Question 3(a) for the case m1 = 9 kg, m2 = 1 kg, k1 = 24 N/m, k2 = 3 N/m,...
A 5 m long cantilever beam has a 5.0 kg mass at the end. Let the deflection (δ) equal 0.07 m at the end. Find the spring stiffness, the frequencies (o and f) and the period. 1. A 0.30 kg mass is suspended by a spring having a stiffness of 0.2 N/mm. Find the deflection, frequencies (o and, and the period. 2. The spring stiffnesses are k1150 N/m and k2 140 N/m. Find the displacements for each spring and mass....
4. (a) Three point masses are attached to a massless rigid rod. Mass m,-1.0 kg is located at x = 1.0 cm, mass m2-2.0 kg at x = 2.0 cm and mass m,-3.0 kg at x-3.0 m. Find the center of mass of the system. (b) Find the center of mass of the four masses as below. mi 2.0 kg at point (1,2) cm; m 3.0 kg at point (2,-3) cm; m -4.0 kg at point (3,-4) cm and m...
1. Springs and a mass are attached to a rigid bar, as shown in Fig 1. The hinges are free to rotate. 0 denotes the rotational angle of the rod, and 0-0 when all springs are not stretched. The mass of the bar and the size of the mass are negligible. Neglect gravitational force, and assume 0 is very small. 1) Derive the equation of motion for this system with Lagrange's method. (20pt) 2) Find the natural frequency of the...
The mass of the uniform slender steel rod, shown in Figure 2, is 3 kg. The system is set in motion with small oscillations about the horizontal equilibrium position shown. (i) Determine the position x for the slider such that the system period is 1 s. (ii) When the pivot is replaced by a built-in support that restricts any rotation at O and the spring is moved to the right-hand end with the 1.2 kg mass removed, calculate the frequency...
PROBLEM 3: (40 points) A rigid massless lever ACB, as shown in Figure 3, is pivoting about point C. A mass mis attached at point A. Assume frictionless pivot point, frictionless pulley, massless pulley, and small angles. The parameters are Ki-30N/m, m=1 kg, K2-40N/m, C-4.35N-s/m, L=0.4 m, a=0.2 m, and b=0.15 m. (i) Draw the Free Body Diagram (FBD) (5 points). (ii) Use Newton's approach to derive the equations of the motion (10 points). (iii) Use Lagrange's method to derive...
Please provide any MATLAB code you used for plotting.
1 1 2 m2 1. Consider the system above. Derive the equation of motion and calculate the mass and stiffness matrices. a) Calculate the characteristic equation forthe case m 9 kg m 1 kg k 24 N/m k2 3 N/mk3- 3 N/m and solve for the system's natural frequencies. b.) Calculate the eigenvectors u1 and u2 c.) Calculate xi(t) and x2(t), given x2(0)-1 mm, and xi(0) - vz(0) -vi(0) 0 d.)...