7-12. Find the rms load voltage v in the amplifier of Figure 7-80 when R (a)...
For the cascade amplifier of the figure, calculate the
polarization voltages
Please clarity answer, thanks!!
1. For the cascade amplifier of the figure, calculate the polarization voltages and current collector of each stage. Also, calculate the voltage gain for each stage and the total voltage gain for cascade amplifier. 2. Repeat the previous steps using a load resistance of 2.2 kΩ 3. Calculate the input and output impedances for the cascade amplifier and the cutoff frequencies (fi) for the cascade...
1.0 kn. RE-390 Ω, r-15 Ω. and ßac-75. 5. For a common-emitter amplifier, Rc Assuming that Rg is completely bypassed at the operating frequency, the voltage gain is (a) 66.7 (d) 75 (b) 2.56 (c) 2.47 6. In the circuit of Question 5, if the frequency is reduced to the point where Xctbypass) RE, the voltage gain (a) remains the same (b) is less (c) is greater 7. In a common-emitter amplifier with voltage-divider bias, Rimlbase) 68 k2, Ri 33...
0.7V, and Va 100V. Find: -For the operational amplifier of Figure 4 assume all transistors have β-100, Find the de emitter currents and the de collector voltage of all transistors. The de voltage at the inputs is OV and the de output voltage is held at 0V (by negative feedback, not shown). Neglect the de base currents for this part. Find the (differential) voltage gain of the amplifier with R-10 k2. Assume the impedance of the capacitor is very large....
7. A voltage amplifier has the following specifications: Av-100 V/V, Rin 110 k 2. Rou-50 92. It is driven by a 10 mV source with a 10 k 2 internal impedance and drives a 7512 load. Determine the load voltage. Answer: 550 m V
The 1 mA. V, ls -VE -15 15 V, in the following differential amplifier circuit, Vcc parameters are given as β, 100, VBE# 0.7 V, pr-25 mV, K.-100 V. transistor Rc-10 kΩ For: RE-150 Ω Rc Rc REE-200 kΩ a) What is the input differential resistance, Rid b) What is the overall voltage gain vV? You c) What is input common mode resistance, d) What is the worst case common mode gain that appear across the two input terminals? (4...
0.7V, and Va 100V. Find: -For the operational amplifier of Figure 4 assume all transistors have β-100, Find the de emitter currents and the de collector voltage of all transistors. The de voltage at the inputs is OV and the de output voltage is held at 0V (by negative feedback, not shown). Neglect the de base currents for this part. Find the (differential) voltage gain of the amplifier with R-10 k2. Assume the impedance of the capacitor is very large....
A CE amplifier utilizes a BJT with β = 100 biased at IC = 0.5 mA; it has a collector resistance RC = 10 kΩ. Find Rin, Ro, and Avo. If the amplifier is fed with a signal source having a resistance of 10 kΩ, and a load resistance RL =10 kΩ is connected to the output terminal, find the resulting Av and Gv. If the peak voltage of the sine wave appearing between base and emitter is to be...
In Figure 9, the transformer primary voltage is 120V and step-downratiois 10:1 Assume the practical diode model. 9. a) i) Name the type of circuit (1 mark) Determine the peak output voltage, Volout) (4 marks) iiI What is the PIV rating required for the diodes (2 marks) D, D3 120 V psecy R Plout) 10 k2 DA Figure 9 b) A certain power supply filter produces an output with a ripple of 100mV peak-to- peak and a dc value of...
What would be the expression for the closed-loop voltage gain A-Vo(t)/v(t) in figure 5 assuing it is an ideal op-am model? 1) 2) What would be the input resistiance of figure 5? 3) What would R, and R2 (from the list below) must be to obtain a voltage gain of A 2.5 1.2 kS2, 1.5 kS2 (2), 1.8 k2, 2.2 k2, 10 k2, 12 k2, 15 k2, 18 k2, 22 k2 +5 V Rs= 1.5 k(2 in(0 5 V VoltageSource...
1. Figure 1 shows a CE power amplifier in which the collector resistor serves also as the load resistor. Assume Bpc Bac 100 a. Determine the dc Q-point (lco and VCEQ). b. Determine the voltage gain and the power gain c. The power dissipated in the transistor with no load. d. The total power from the power supply with no load e. The signal power in the load with a 500 mV input. f. What changes would be necessary to...