8.33 Link AB is to be made of a steel for which the ultimate normal is...

Question

Question

Answer 1

Answer #1

Drawing the Frel-body diagram? Bx12) KN = 9.6kN FAC 35 - 20kn Dy 0.4m 0.4m 0.4m Taking moment about point oa. E MO =0) -(FAB

Answer 2

Similar Homework Help Questions

1.41 Link AB is to be made of a steel for which the ultimate normal stress...

1.41 Link AB is to be made of a steel for which the ultimate normal stress is 450 MPa. Determine the cross-sectional area of AB for which the factor of safety will be 3.50. Assume that the link will be adequately reinforced around the pins at A and B. 8 kN/m 35° C 20 kN 0.4 m 0.4 m 0.4 m Fig. P1.41 1.41 Link AB is to be made of a steel for which the ultimate normal stress is...
1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins...

1.51 In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 150 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that ink BD is not reinforced around the pin holes Front view 18 mm Side...
Problem 4 (3pts) The beam AB is supported by a single-shear pin connection at joint A...

Problem 4 (3pts) The beam AB is supported by a single-shear pin connection at joint A and by a double-shear connection to member (1) at joint B. Member (1) is connected to the support at C with a double-shear pin connection. Member (1) has a cross-sectional area of 100 mm and a yield strength of 340 MPa. The pins at A, B, and C each have a diameter of 12 mm, and an ultimate shear strength of 270 MPa. Specifications...

In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are...

In the steel structure shown, a 6-mm-diameter pin is used at C and 10-mm-diameter pins are used at B and D. The ultimate shearing stress is 159 MPa at all connections, and the ultimate normal stress is 400 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. (Round the final answer to three...
1.52 Solve Prob. 1.51, assuming that the structure has been redesigned to use 16-in.-diameter pins at...

1.52 Solve Prob. 1.51, assuming that the structure has been redesigned to use 16-in.-diameter pins at A and C as well as at B and that no other changes have been made. A in. 8 in. B C 4 in. 6 in. Fig.P1.51 1.51 Link AC is made of a steel with a 65-ksi ultimate normal stress and has a 2-in. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter...
show every step 2·The link BC is 1-6mm thick (into the page) and has width, w(that...

show every step 2·The link BC is 1-6mm thick (into the page) and has width, w(that is, the cross section of the link is t by w). The link is made of steel, with an ultimate strength of 450 MPa in tension. What should the width of the link be if 40 480mm the structure is designed to support a load of P- 20 kN with a factor of safety equal to 3. (Hint: BC is a two-force member.) Ans:...

5.3 m 7.5 m B D (1) 60 8 m 3.4 m P The rigid T...

5.3 m 7.5 m B D (1) 60 8 m 3.4 m P The rigid T shape ABD is supported by an elastic rod BC (with a 35 mm diameter). Pin A (30 diameter) is in single shear. mm Double shear pins B and C are 24 mm diameter. Rod BC has a yield stress of 250 MPa and all pins have a ultimate shear stress of 330 MPa. Take P 50 kN and determine: Normal stress in BC 1...
Question 2: (15 marks) Bracket ABC has loads applied as identified in Figure 2. A steel control r...

please label with detailed steps ! thank you Question 2: (15 marks) Bracket ABC has loads applied as identified in Figure 2. A steel control rod A with ultimate normal stress of 600 MPa is attached to point B. At point C the steel pivot pin has an ultimate shearing stress of 350 MPa. Assuming a factor of safety of 3.3 determine: (i) The minimum acceptable diameter of the control rod AB (ii) The minimum acceptable diameter of the pivot...
The rods AB and CD are made of steel having a failure tensile stress of O...

The rods AB and CD are made of steel having a failure tensile stress of O fail = 510 MPa. Using a factor of safety of F.S. = 1.75 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. В. D 6 kN 5 kN 4 kN A C 4 2 m ----2m- -3 m -3 m Figure: 07_PROB_076