Homework Answers
Add Answer to:
Q. 5(20 points) Design a transistor amplifier to supply a LED. The LED is required to...
The component values for the npn-transistor amplifier circuit are R = 665 Q, Vcc= 20 V,...
The component values for the npn-transistor amplifier circuit are R = 665 Q, Vcc= 20 V, VB= 2.4 V, and RB= 85k a) The graphon the last page shows the characteristics for the transistor in the above circuit Construct the load line for th is transistor circuit and draw it into the IC vs. VCE graph. Briefly state how you determine the load line. b) Determine the base current, assuming that the transistor is made of silicon. c) Determine the...
We design a voltage amplifier using a BJT following the plan laid down in the handout "Notes on common emitter...
We design a voltage amplifier using a BJT following the plan laid down in the handout "Notes on common emitter transistor amplifier 8 IN RB Design an amplifier with a Gain VoutVinl30 Assume the transistor gain is B 100. Let Vcc 15 V Choose VCE Vcc-VCE.Sat Choose Ic.o-10 mA. 1. Determine values of resistors Rc, RE, and RB so that the gain is essentially independent of the value of β 2. State and satisfy the load-line relation between lc.a and...
4. Lab VIII: Experiment VII The Bipolar Junction Transistor (BJT) Characteristics The bipolar junction transistor (BJT)...
4. Lab VIII: Experiment VII The Bipolar Junction Transistor (BJT) Characteristics The bipolar junction transistor (BJT) is a three-terminal solid state device widely used as an amplifier (or switching) device. It consists of two n-type materials sandwiched by p-type material (npn) or two p-type and n-type. The terminals (sections) are known as emitter E, base B and collector C. Two currents and two voltages uniquely describe the behavior of the device. The third current/voltage can be determined through KCL/KVL. See...
Design a transistor based relay driving circuit to turn ON and Turn OFF a 240 Volt 50 Hz AC motor...
Design a transistor based relay driving circuit to turn ON and Turn OFF a 240 Volt 50 Hz AC motor using the output of a microcontroller assumed to be 5v at 5mA. The circuit should included a 12V relay which requires 60 mA of switching current, assume the relay provides enough isolation between the micro controller and the 240 V supply. Detail all calculations relating to the transistors.
Electronics-common emmitter amplifier. Pls be try to be helpful Im trying to study here in this book example.. However im kinda lost and i cant follow the correct answers they got.. could someon...
Electronics-common emmitter amplifier. Pls be try to be
helpful
Im trying to study here in this book example..
However im kinda lost and i cant follow the correct answers
they got.. could someone pls help me..
I just wanna learn this, i hope u can help me learn by showin
clear and corect solutions on how to properly got the
answer..
Also especially on finding the values on the laod line
analysis, im lost.
Pls help
Any helpful help would...
Design a BJT amplifier based on the specifications provided in the table below. Your design shoul...
THE STEPS TO DO SO:
Design a BJT amplifier based on the specifications provided in the table below. Your design should be insensitive to β variations, and both the input and the output should be AC coupled as in Fig. 1. Supply Voltage, Vcc Load Resistance, RL Transistor's Current Gain, β Relative Variation of lc for VBE-0.7 ± 0.1 V 0-to-Peak Output Swing, Vo Voltage Gain, A Input Resistance, R THD for 5kHz IV (0-to-peak) Sine Wave Output Voltage, V。S5%...
im currently doing an assignment where i must design a two stage bipolar transistor, i just...
im currently doing an assignment where i must design a two stage
bipolar transistor, i just need the calculations and values for
each component and then i can run simulated experiments and
complete my work
here is the schematic
the transistor used is the BC846B
the supply voltage is 15 v
the collector currents 1 (ICq1) = 1.5mA
the collector current 2 (ICq2) = 7.5 mA
output voltage swing= max
frequency response = 50- 20 khz
i must calculate the...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a transformer which has a rms secondary voltage of 15.6V. The primary of the transformer is connected to a 50Hz, 230VRMS power supply. A 2700uF filter capacitor is used. A current of 1.5 Amp is drawn from the supply. (i) Sketch a schematic diagram of the setup. (ii) Calculate the mean de output voltage. Assume each power diode has a forward voltage drop of 1...
The component values for the npn-transistor amplifier circuit are R = 665 Q, Vcc= 20 V, VB= 2.4 V, and RB= 85k a) The graphon the last page shows the characteristics for the transistor in the above circuit Construct the load line for th is transistor circuit and draw it into the IC vs. VCE graph. Briefly state how you determine the load line. b) Determine the base current, assuming that the transistor is made of silicon. c) Determine the...
We design a voltage amplifier using a BJT following the plan laid down in the handout "Notes on common emitter transistor amplifier 8 IN RB Design an amplifier with a Gain VoutVinl30 Assume the transistor gain is B 100. Let Vcc 15 V Choose VCE Vcc-VCE.Sat Choose Ic.o-10 mA. 1. Determine values of resistors Rc, RE, and RB so that the gain is essentially independent of the value of β 2. State and satisfy the load-line relation between lc.a and...
4. Lab VIII: Experiment VII The Bipolar Junction Transistor (BJT) Characteristics The bipolar junction transistor (BJT) is a three-terminal solid state device widely used as an amplifier (or switching) device. It consists of two n-type materials sandwiched by p-type material (npn) or two p-type and n-type. The terminals (sections) are known as emitter E, base B and collector C. Two currents and two voltages uniquely describe the behavior of the device. The third current/voltage can be determined through KCL/KVL. See...
Electronics-common emmitter amplifier. Pls be try to be
helpful
Im trying to study here in this book example..
However im kinda lost and i cant follow the correct answers
they got.. could someone pls help me..
I just wanna learn this, i hope u can help me learn by showin
clear and corect solutions on how to properly got the
answer..
Also especially on finding the values on the laod line
analysis, im lost.
Pls help
Any helpful help would...
THE STEPS TO DO SO:
Design a BJT amplifier based on the specifications provided in the table below. Your design should be insensitive to β variations, and both the input and the output should be AC coupled as in Fig. 1. Supply Voltage, Vcc Load Resistance, RL Transistor's Current Gain, β Relative Variation of lc for VBE-0.7 ± 0.1 V 0-to-Peak Output Swing, Vo Voltage Gain, A Input Resistance, R THD for 5kHz IV (0-to-peak) Sine Wave Output Voltage, V。S5%...
im currently doing an assignment where i must design a two stage
bipolar transistor, i just need the calculations and values for
each component and then i can run simulated experiments and
complete my work
here is the schematic
the transistor used is the BC846B
the supply voltage is 15 v
the collector currents 1 (ICq1) = 1.5mA
the collector current 2 (ICq2) = 7.5 mA
output voltage swing= max
frequency response = 50- 20 khz
i must calculate the...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a transformer which has a rms secondary voltage of 15.6V. The primary of the transformer is connected to a 50Hz, 230VRMS power supply. A 2700uF filter capacitor is used. A current of 1.5 Amp is drawn from the supply. (i) Sketch a schematic diagram of the setup. (ii) Calculate the mean de output voltage. Assume each power diode has a forward voltage drop of 1...
Most questions answered within 3 hours.
-
In Drosophila, the transition from the syncytial blastoderm
stage to the cellular blastoderm stage is a...
asked 21 minutes ago -
Project management question:
Name 3 different types of resources (hint: humans are one
type)
asked 33 minutes ago -
Consider the following reaction: C 2H 2( g) + 2H 2( g) C 2H 6(
g)...
asked 41 minutes ago -
Consider a 1.0 L buffer containing 0.092 mol L-1 HCOOH and 0.100
mol L-1 HCOO-. What...
asked 50 minutes ago -
Koch Realty has owned a vacant land with a FMV of
$775,000 and an adjusted basis...
asked 55 minutes ago -
It is estimated 29% of all adults in United States invest in
stocks and that 85%...
asked 55 minutes ago -
What does a 2-sided p value of 0.04 mean? (I am not asking if it
is...
asked 1 hour ago -
A parallel-plate capacitor is made from two aluminum-foil
sheets, each 7.8 cmcm wide and 5.1 mmlong....
asked 1 hour ago -
1. why is toluene a stronger nucleophile than benzene?
2.why is phenol a stronger nucleophile than...
asked 1 hour ago -
4. How can you solve for the density of the liquid from the
slope? Please show...
asked 1 hour ago -
when 2053 j of heat is added to 46.3 g of hexane C6H14 the
temperature increases...
asked 1 hour ago -
I need new and unique answers, please. (Use your own words,
don't copy and paste), Please...
asked 1 hour ago