Please show all work, thank you!
Please show all work, thank you! A one toil column is being set in place by...
PLEASE SHOW ALL WORK STEP-BY-STEP AS MUCH AS POSSIBLE 0.75 in 0.75 in. 8.71 A wedge A of negligible weight is to be driven between two 100- ib blocks B and C resting on a horizontal surface. Knowing that the coeffi- cient of static friction at all surfaces of contact is 0.35, determine the smallest force P required to start moving the wedge (a) if the blocks are equally free to move, (b) if block C is securely bolted to...
Please show all work made. Thank you Problem #2 For this problem please use the figure below , e=0.52 G, 2.66 10 ft □ Dry Sand Clay a. Calculate the variation of, u, and σ' with depth. b. If the water table rises to the top of the ground surface, what is the change in the effective stress at the bottom of the clay layer?
Can you show all steps to solve the question? Thank you 2. A solid uniform sphere and a uniform spherical shell, both having the same mass m and radius R, roll without slipping down a hill that rises at an angle ? above the horizontal. Both spheres start from rest at the same vertical height h 10.0 m. Given lem mR2 and sphere shelt S) () mR2. You may use energy (a) How fast is the solid sphere moving at...
Please see question below. Please double check all work and units/unit conversions. Show all work. Thank you! Question 2 A charge of +6 micro-coulombs is placed at the bottom left corner of a rectangle, a charge of -6 micro-coulombs is placed at the top left corner of a rectangle, a charge of +8 micro-coulombs is placed at the bottom right corner of a rectangle, and a charge of +8 micro-coulombs is placed at the top right corner of a rectangle....
Please answer the questions in each photo thank you! Page 2 of 3 HYS 181: Ropes and Pulleys Names: 1.0 kg 3. The 1.0 kg block in the figure is tied to the wall with a rope. It sits on top of the 2.0 kg block. The lower block is pulled to the right with a tension force of 20 N. The coefficient of kinetic friction at both the lower and upper surfaces of the 2.0 kg block is th=0.40....
ANSWER IS 0.8KN SHOW ALL WORK PLEASE!!!!! A 100-kg block is pushed up a 30° incline that is 10 m long. If the coefficient of friction between the block and the incline is 0.1, the constant force parallel to the incline that is required to move the block from rest at the bottom of the incline to the top in 3 s is approximately
Could you please show your work as well? Thank you! A 295-kg log is pulled up a ramp by means of a rope that is parallel to the surface of the ramp. The ramp is inclined at 30.0 with respect to the horizontal. The coefficient of kinetic friction between the log and the ramp is 0.800, and the log has an acceleration of 0.900 m/s2. Find the tension in the rope
Please show all work and steps. Any help will be appreciated and thank you for your time! A thin ring of outer radius, ro, inner radius, ri, and weight, W, with an initial counterclockwise angular velocity, wo, is placed in the corner formed by the floor and a vertical wall. Denoting the coefficient of kinetic friction between the thin ring and the wall and the floor as lk, derive an expression for the time required for the thin ring to...
Please show all work and explanation. Thank you. Problem 2. A 6 in thick partition is 16 ft high and is designed to carry its own weight plus lateral wind load. Consider it be constructed of hollow concrete block and type S mortar (fm = 2500 psi) and to be simply supported top and bottom. Determine the design wind pressure.
Please show all work thank you 10). Adoor seen from above in the figures below) has hinges on the left hand side. The magkatudes of anforces arkaQual. Rank from smallest to greatest the torque applied by the force on each of the following situations. Explain how you determined your rank.