Q.6) Determine the tension in the cable CD and the support reactions Ax and Bx. The...
Hinges A and B along with cable CD support the rigid gray plate. Hinge B provides the axial thrust along the y-axis. KN 6.6 ft 6.0 ft 13.0 ft 6.0 ft - > 2.8 kip Determine the tension in cable CD and the reaction force components that hinges A and B exerts on the gray plate in pounds. (Indicate the direction with the sign of your answer. Neglect the moments provided by hinge A and B. Point D is directly...
Q. 3 The tension in cable AB is 800 N. Determine the reactions at the fixed support C. (1 point) -4 m С 5 m 4 m А B (6, 0, 4) m
What is the cable tension in the éach of the situations? Draw a force diagram for each situation. (Note: total length of beam L 6 m) Note: Hinges supply both a horizontal and a vertical force. Please select the left most place on the object (at the hinge) as the pivot. W the weight of the beam. Parts a and b have been omitted. c) 7. rod on a hinge W 60 N d) rod on a hinge 0 45...
Determine the required tension in cable BC if the resultant of the three forces exerted at Point B is to be vertical. The required tension in cable BC is _____N Determine the corresponding magnitude of the resultant. The corresponding magnitude of the resultant is _____N Consider the force system shown in the figure below where P = 530 N. - 840 mm - L= 1160 mm 800 mm B 780 N
Knowing that the tension in cable BCis 760 N, determine the resultant of the three forces exerted at Point B of beam AB 840 mm- L= 1160 mm 800 mm 13 12 780 N 500 N The magnitude of the resultant of the three forces is The direction of the resultant of the three forces is γ N.
Determine the tension in cables AB, BC, and CD necessary to support the 11-kg and 17-kg traffic lights at B and C, respectively. Also, find the angle θ. 15°) в OP OP OP Q Tap image to zoom Part A Determine the tension in cable AB. Part A Determine the tension in cable AB Express your answer to three significant figures and include the appropriate units. TAB= 417N Correct Part B Determine the tension in cable BC Express your answer...
AC-CD- BC Exercise IV 20 PT a- Determine the reactions at the supports. b- Determine the force in each member of the truss c- State if the members are in tension or 3 ft compression d- If the maximum allowed in each beam is 400lb in tension and 600lb in compression, determine the maximum of admissible load P. 2 ft 2 ft Exercise V: 40 PT 1.6 kN 200 _ 400 mm + 45 The angle strut is welded to...
Knowing that the tension in cable AC is 2180 N, determine the components of the force exerted on the plate at C. (Round the final answers to the nearest whole number.) 2. 360 mm- lhigedal and Vtioal 920 inm fcos (a) lo 9=tSin (a) 600 mm 900 mm Groen: Tre = 2180N 99tm 960 AC CA A crate of mass 90 kg is held in the position shown. 3. fe Bodly biaghom 0.6 m 0.6 m- D.ot0.6=1.2 90 Ky B...
A temporary support steel frame (E 200 GPa) is made of 30-mm diameter solid circular steel rods (members AB and CD), and 22-mm diameter solid circular steel rods (members BC and AD), al pin connected at the turnbuckle corners A, B, C, and D (see Figure below). The steel frame is braced by two cables AC and BD. A turnbuckle is fitted to cable AC and tightening it will induce tension 3m in cable AC. Determine the largest allowable tension...
750 N 1) What is the angle between r, and the 750 N force that you would use if you were to calculate the moment that the force creates about point C? (You do not need to actually calculate the moment.) 200 mm - 100 mm 2) Bar AB is inclined at 50 from the vertical. A 100-N force is applied to the bar at end B. Determine the magnitude and direction of the moment this force creates at a...