Ulston cylinder device contains a liquid-vapor xture at 300K. During a constant pressure added to water....
A frictionless piston-cylinder device contains a saturated liquid-vapor mixture of water at 373K. During a constant pressure process, 600 kJ of heat is transferred to the surrounding air at 300K. Asa result, part of the water vapor contained in the cylinder condenses. Determine (1) the entropy change of the water, (2) the entropy change of the air (3) the total entropy generation during this process.
A frictionless-piston-cylinder device contains a liquid-vapor mixture of water at 200°C. During a constant- pressure process, 500 kJ of heat is transferred to the surrounding air at 20°C. As a result, part of the water vapor contained in the cylinder condenses. a) Draw a schematic of your system including the boundary and all relevant energy transfer. (2 pts) b) Determine the entropy change of the water, in kJ/K. (3 pts) c) For the extended system (system + surroundings), write an...
(a) An insulated piston cylinder device contains 5 L of saturated liquid water at a constant pressure of 150 kPa. The cylinder was equipped with the electric heater inside it. The liquid is heated at constant pressure until it becomes saturated vapour. Determine the entropy change of the water during this process in kJ/K. (10 Marks) (b) A stream of refrigerant R134a enters a steady flow device at 100 kPa, 50 °C at a rate of 1 kg/s. Two streams...
Question 11 A piston cylinder-device contains 12 kg of steam at 100 kPa and 175°C. Over time, the steam in the piston-cylinder device isobarically loses heat to its surroundings until it reaches a temperature of 99.61"C and all the vapor in the piston has condensed into liquid. a. Determine the entropy change of the steam, in kJ/K b. For the steam and its surroundings, determine the total entropy change associated with this process, in kJ/K. The temperature of the surroundings...
Problem 5- A piston-cylinder device initially contains steam at 3.5 MPa, superheated by .10°C. Now, steam loses heat to the surroundings and the piston moves down, hitting a set of stops, at which point the cylinder contains saturated liquid water. The cooling continues until the cylinder contains water at .200C. Determine the initial temperature of the steam a. b. Sketch the process on a P-v an T-v diagram Determine the initial specific enthalpy, in kJ/kg d. Determine the enthalpy change...
An insulated piston-cylinder device contains 5 L of saturated liquid water at a constant pressure of 175 kPa. Water is stirred by a paddle wheel while a current of 8 A flows for 45 min through a-resistor placed in the water. If one-half of the liquid is evaporated during this constant pressure process and the paddle-wheel work amounts to 400 kJ, determine the voltage of the source. Also, show the process on a P-v diagram with respect to saturation lines.
1. (42 points) A piston-cylinder device contains 6 kg of steam at 100°C with a quality of 50 percent. This steam undergoes two processes as follows: 1-2 Heat is transferred to the steam in a reversible manner while the temperature is held constant until the steam exists as a saturated vapor. 2-3 The steam expands in an adiabatic, reversible process until the pressure is 15 kPa. (a) (24 points) Fill in the table using the given and determined properties. You...
Round your final answers to the nearest integer. A piston-cylinder device contains 4.37 kg of steam at 100°C with a quality of 60 percent. This steam undergoes two processes as follows: 1-2 Heat is transferred to the steam in a reversible manner while the temperature is held constant until the steam exists as a saturated vapor. 2-3 The steam expands in an adiabatic, reversible process until the pressure is 15 kPa. (a) Determine the heat added to the steam in...
A frictionless piston-cylinder device contains 16 lbm of superheated water vapor at 40 psia and 600oF. Steam is now cooled at constant pressure until 70 percent of it, by mass condenses. Determine the work done during this process.
3. (5 pts) An insulated, vertical piston-cylinder device initially contains 2 kg of water at 70°C. The mass of the piston is such that it maintains a constant pressure of 400 kPa inside the cylinder. Water at 1000 kPa and 500°C is allowed to enter the cylinder from a supply line until the instant that the last. drop of liquid in the cylinder vaporizes. Determine the mass of the steam that has entered.