Please, can you draw ammeter diagrams for both circuits? first to measure i1 and second to measure i2 in both circuits. Thanks!
Something like this:
Please, can you draw ammeter diagrams for both circuits? first to measure i1 and second to...
2. (Short Circuits) An Ammeter is a device that can measure current through a circuit compo- nent. It is devised to be a device that has a VERY LOW internal resistance r. You use the device by connecting the device in series with the branch of the circuit you want to measure the current through. Suppose you accidentally connected the ammeter in parallel with a bat- tery and another resistor (with resistance R»r). Using Kirchoff's rules, show that when s...
Measure I1, I2, I3, I tot and V. Next calculate Req
you can find the equation in the lab manual. Then add together
I1+I2+I3, next calculate Icalc.
4) Now Make this circuit, it is the same as Figure 7 in the lab manual; I tot 1.11 12 13 (Al- +2 +3 Figure 7: Schematic of three resistors in parallel. I used 11, 12, 13 and I tot this is the same as A1, A2, A3 and A1+2+3. Measure 11, 12,...
Digital Circuits 1) Draw block diagrams to implement a 4 to 1 with 4 bits multiplexer. The data input lines are 4 bits wide. Please decide how many selects do you need. And write the final equation for inputs and output in both your report and block diagram. Do the simulation.
5. In this problem, you will design new logic diagrams for problems 1 c and 4 c, optimizing the solution to use a minimum number of gates and chips. You may use whatever real chips you like in this problem. Assume that these two circuits make up a single design so that unused parts of one chip for the first circuit can be used for the second circuit. Use the following activation levels: B and C are active-high, A is...
In the table below, draw two Lewis dot diagrams. One, enforcing the Octet rules and a second, enforcing the "lowest charge rules"Note: the two diagrams may actually be the same but draw them both array. Below the table, for each species tell which model is the better one and explain why it's better than the other model you drew of the same species. I will give you an example for Carbon monoxide in the first row. In this case, both...
Hello, can you please solve this question? I1 = 1.4 mA and I2 =
2.4 mA ?
4 HT tsi If I = 1.4 mA and I 2 = 2.4 mA and u, o 1 v and uq=1 y II, Rin what's the value F of R1, R2 and RS RS?
please answer both 4 and 5 if possible thank you
Multi-loop complex circuits: In All the circuit problems below, use Kirchhoffs Law. The use of Kirchhoff's law greatly simplifies the circuit problem especially with multi loop cireuits. 4. (a) Calculate the currents I, Iz and the emf of the battery e in the circuit below (0.71 A. 2.3 A and 19 Vrespectively) ) Calculate the voltage and power dissipated across the 4.5 resistor (10 V and 24 W) 3.00 4.5Q...
Draw the reaction and reaction mechanism for the reaction of
both
cis
and
trans
stilbene with Br2
as part of your prelab procedure.
Note: I'm not sure what the
mechanisms look like so that's why I'm having trouble with the
products. Please, if you can, draw out the mechanisms for both of
these!! Thanks.
cis-stilbene trans-stilbene
Can you please explain to me how to draw a graph for both of
these I already did the motion diagrams
For the problem 4-7 below draw a sketch, a motion diagram, and graphs. 4. [pnt] While you are driving down a country road at dusk with a velocity of 22 m/s, a deer suddenly runs across the road in front of you. You apply the brakes, reducing your velocity to 7 m/s in 5 s as you avoid hitting...
Can
you please explain why the answer to these questions related to
electric current are those circled? Please provide a detailed
explanation thanks!
QUESTION 1 If I connect a bulb to a battery, the bulb lights up with a certain brightness. What will happen if I connect a second bulb? . A) The first bulb will be the same brightness as before, but the second bulb will be dimmer B) The first bulb will be the same brightness as before,...