600 mm 600 mm "в 25 mm 50 mm If the gap between C and the...

Question

Question

Answer 1

Answer #1

420.2 mm, &K 0 2 using equilibrium condition, 2 Р z 300 x10² R,+ R2 > Rit R2 using compatibility condition, 4 + 4 - 0-2 R, &

Answer 2

Similar Homework Help Questions

If the gap between C and the rigid wall at Dis initially 0.15mm, determine the magnitudes...

If the gap between C and the rigid wall at Dis initially 0.15mm, determine the magnitudes of the support reactions at A when the force P = 283 kN is applied. The assembly is made of a material with E=196GPa. Express your answer in KN 600 mm -600 mm -- 25 mm 50 mm
Problem 4.46 Part A If the gap between C and the rigid wall at Dis initially...

Problem 4.46 Part A If the gap between C and the rigid wall at Dis initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 200 kN is applied. The assembly is made of A36 steel. Enter your answer, separated by a comma. 600 mm - -600 mm -- -0.15 mm C B 25 mm ANSWER: FA, FD = kN
Determine the support reaction at C when an axial force of P reaction at C when...

Determine the support reaction at C when an axial force of P reaction at C when an axial force of 40 05 kN is applied . The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. (Figure 1) When no load is applied to the assembly, the gap between end C and the rigid support is 0.5 mm Express your answer to three significant figures and include a riate units Units CVatue Figure < 1of1...

Two identical steel rods AB and CD each have a length L = 6 m and...

Two identical steel rods AB and CD each have a length L = 6 m and cross-sectional areas of 500 mm2, and are used to support the rigid beam, which is pinned at A and maintains an initial gap of 0.2 mm to support F. If a vertical force P is applied at the end of the beam, (i) (ii) determine the value of P required to close the gap If P = 12 kN, determine the force in rod...
The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC

The 2014-T6 aluminum rod AC is reinforced with the firmly bonded A992 steel tube BC. (Figure 1) When no load is applied to the assembly, the gap between end C and the rigid support is 0.5 mm. Part A Determine the support reaction at C when an axial force of P= 340 kN is applied. Part B Determine the support reaction at D when an axial force of P = 340 kN is applied.
steel copper A pastauer ay cogper tulbe Steel 0.mm Gap lahun prts sa.l mn Cross-cecC areas 300mm for batte anateials s...

steel copper A pastauer ay cogper tulbe Steel 0.mm Gap lahun prts sa.l mn Cross-cecC areas 300mm for batte anateials s y 220 MPa Es10GPa OcY=70 M Pa Ec 101G Pa O.asm 2 The support consists ofa solid steel post surrounded by a copper tube as shown in the figure assume end plate A is a rigid body). Before the load is applied the gap between these two parts is 0.1 mm. The cross-section areas are 300 mm2 for both...

Question 15 A steel rod of 10.5-mm diameter is held snugly (but without any initial stresses)...

Question 15 A steel rod of 10.5-mm diameter is held snugly (but without any initial stresses) between rigid walls. dbolt diameter bolt AT Clevis drod After fixina the rod, temperature dropped by 24 degrees celsius For steel consider: . Young Modulus: E-200 GPA Linear temperature expansion coefficient for steel is 23x10-6 (1/C) Determine in kN the value of the reaction force P at the wall support at end B
Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240...

Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240 mm2. Link CE is made of aluminium (E 72 GPa) and has a cross-sectional area of 300 mm2. Knowing that they support rigid member ABC, determine the maximum force P that can be applied vertically at point A if the deflection of A is not to exceed 0.36 mm. (Round the final answer to two decimal places.) 995 mm A 150 mm E 225...
0.7 mm 6 BL Problem 3 - Thermal Stress (25 pts) The center rod CD of...

0.7 mm 6 BL Problem 3 - Thermal Stress (25 pts) The center rod CD of the assembly is heated from T, = 25°C to T2 = 200°C using electrical resistance heating. At the lower temperature T, the gap between C and the rigid bar is 0.7 mm. Determine the force in the rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel, and each has a cross-sectional area of 125 mm²....

Question 35 300 mm 18 in 4.5 ft 60 mm 40 mm Fig. P2.33 2.34 For...

Question 35 300 mm 18 in 4.5 ft 60 mm 40 mm Fig. P2.33 2.34 For the composite block shown in Prob. 2.33, determine (a) the value of h if the portion of the load carried by the aluminum plates is half the portion of the load carried by the brass core, (b) the total load if the stress in the brass is 80 MPa Fig. P2.35 2.35 The 4.5-ft concrete post is reinforced with six steel bars, each with...