In a certain TLC experiment the following data were obtained. (All measurements listed are from the bottom of the plate). What is the Rf for spot A?
Original Solvent depth: 1.00 cm
Final Solvent front: 8.00 cm
Original Position of spots: 2.00 cm
Final Position of spot A: 5.00 cm
A) 0.625
B) 0.50
C) 0.40
D) 5.00
Please explain
In a certain TLC experiment the following data were obtained. (All measurements listed are from the...
CAN SOMONE PLEASE HELP. above is a picture of two TLC plates
with spots on them. could somone PLEASE PLEASE PLEASE help me get
their measurmentS (in milimeters) and help me calculate their Rf
values!!! I promise to rate u good if you could help!!! Im so
confused!!! THANK U SM
-solvent front scluent front Acetaminophen (A Afine (caf) Unknown mixture Phenacetin (Phn) Salicyamide (sal) Plate 2 Untuan unknown ixture mixture duplicate spots Plate 1 ASSIGNMENT In this experiment, TLC...
The mass of the cart is 0.365 kg. The rest of the data can be obtained from the graph above. All answers below must be correct to 3 significant figures. Units are required if not stated. What the final speed of the cart predicted by the work done by the rubber band, assuming that friction negligible? Vpred What the percent difference between between the predicted and measured final speed, expressed as a percent of the measured speed? Percent difference between...
2. If two different compounds have the same Rr value, how might they be identified using paper chromatography? 3. Why is it important to keep the spots on the paper as small as possible? 4. If the solvent pool at the bottom of the beaker touched the spots on the 1.5cm line, what would happen to the spots? How would you address this error? 5. If you were teaching a student how to do paper chromatography, what three pieces of...
if applicacable, please write clear stepwise mechanism for all
synthetic transformations, showing important internediates where
appropriate. only do this if applicable for this lab.
Experiment SD Column Chromatography Running the Reaction. Once sodium borohydride has been added to the reaction meture Isee next paragraph take samples at the times just indicated. Because this must be done in such a short time you must be well prepared before starting the reaction. One person should be the timekeeper, and the other person...
QUESTIONS TO ANSWER:
Prepare a table of all chemicals used with the structure and
purpose of each.
Calculate the theoretical yield by finding limiting reactant of
the experiment by converting reactants to product (remember to show
all calculations used)
Calculate the percent yield using the limiting reactant
Calculate the Rf for triphenylmethanol. If there are two dots,
determine which one is triphenylmethanol.. ( I did not provide
data. Please let me know how I Would do this if I did)...
Only need help with 5,6,7
and mechanism
FTIR and NMR Spectra After completing a reaction and working up the products, it is still necessary to confirm that the correct product was formed. The most common tools used for this analysis are Fourier Transform Infrared (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopy. In the virtual laboratory, 'H and C NMR spectra are available. Details on interpreting FTIR and NMR spectra are found in your textbook. Your instructor may or may not...
Need help, numbers 3-6 please show work. and fill out table of
chemicals for all chemical used.
calculate mmol in the table as well show work please
and each of these must be listed in its own row. There are 10 column headings: IUPAC name OR common name, structure, CAS number (Chemical Abstract Service number) molecular mass, melting point (if applicable), boiling point (if applicable), solubility (in water, if applicable), density, amounts to be used in the experiment, and the...
Experiment Write Up Proposal You will write up a synthesis procedure for one reaction that could be potentially run in a face- to-face Chem 2321 lab session. Your proposal will include an introduction and procedure. The procedure will include step-by-step instructions for running the reaction (including reaction monitoring), work-up. (product isolation and purification), and analysis (characterization). You will need to include sample calculations for percent yield and provide sample spectra analysis. You must upload your proposal as a single document...
I need help with questions 5,
6, & 7. The FTIR and NMR is provided. I also need help creating
a reaction mechanism using the following:
Starting material: methyl acetate.
Solvent: diethyl ether
Reagent: sodium methoxide
Product: methyl acetoacetate
THANK YOU!!!!!
11-8: Claisen Condensation - 1 For this assignment, the target compound that you should synthesize is methyl acetoacetate.This is another carbonyl addition variation. Examine the product and determine which ester is the nucleophile and which is the electrophile. Keep...
I need help with questions 5, 6, & 7. The FTIR and NMR is
provided. I also need help creating a reaction mechanism using the
following:
Starting material: 1,7-Dimethyl-heptanedioate
Solvent: Diethyl ether
Reagent: sodium methoxide
Product: 3-oxo-cyclohexane carboxylic acid methyl ester
THANK YOU!!!!!
Ö 11-11: Dieckmann Reaction For this assignment, the target compound that you should synthesize is 2-oxo-cyclohexane carboxylic acid methyl ester.This is an intramolecular carbonyl addition variation. Examine the product and determine which ester is the nucleophile and...