ANS :- FALSE
given that
sample frequency (fs)=8000
output freuency=1000
because according to the oscillation frequency formula
=( fs/4 )
=8000/4
=2000 hz
so it gives the output frequency is 2000 hz not 1000hz
>>THANK YOU PLEASE UP VOTE<<
Question 3 The pole-zero plot of a sinusoidal oscillator filter is shown below. If the system...
The pole-zero plot of a cosine oscillator filter is shown below. The oscillation frequency is one quarter of the sampling frequency (Fs/4). Pole-Zero Plot for the Non-Damped Cosine Oscillator zp R-1 0.8 06 0.4 0.2 zct zc2 2nd order -0.2 -0.4 -0.6 -0.8 -1 zp -1 -0.5 0.5 Real Part O True False Imaginary Part
2. Consider a second IIR filter a. Determine the system function H(z), pole-zero location (patterns), and plot the pole-zero pattern. b. Determine the analytical expression for frequency response, magnitude, and phase response. c. Choose b so that the maximum magnitude response is equal to 1. d. Plot the pole-zero pattern and the magnitude of the frequency response as a function of normal frequency.
2. Consider a second IIR filter a. Determine the system function H(z), pole-zero location (patterns), and plot...
please show all steps and matlab plot ,
5) Design a one-pole, one-zero passive filter to have a low-frequency gain of -32 dB, a high-frequency gain of 0 dB, and a cutoff frequency of 2,000 Hz. Specify the circuit and all component values. Use Matlab to plot the magnitude and phase frequency response for your filter.
5) Design a one-pole, one-zero passive filter to have a low-frequency gain of -32 dB, a high-frequency gain of 0 dB, and a cutoff...
Below is the zero and poles plot of a system. What is the magnitude response of this system? Pole/Zero Plot 0.5 0 0.5 0.5 0 Real Part 0.5 H(J) : (exp(2*90i*theta)-2"exp(%itthet exp(2-i.6)-2 exp(i-0)+2 exp(2 i.)-exp(i.0)+0.5 Your last answer was interpreted as follows: CHR The variables found in your answer were: [e] Incorrect answer.
Below is the zero and poles plot of a system. What is the magnitude response of this system? Pole/Zero Plot 0.5 0 0.5 0.5 0 Real Part...
Topics: Filter Design by Pole Zero Placement PROBLEM Problem #2 . a) Design a simple FIR second order filter with real coefficients, causal, stable and with unity AC gain. Its steady state response is required to be zero when the input is: xIn]cos [(T/3)n] u[n] H(z) R.O.C: answer: b) Find the frequency response for the previous filter. H(0) c) Sketch the magnitude frequency response. T/3 t/3 d) Find the filter impulse response. h[n] e) Verify that the steady state step...
Problem #1. Topics: Z Transform Find the Z transform of: x[n]=-(0.9 )n-2u-n+5] X(Z) Problem #2. Topics: Filter Design, Effective Time Constant Design a causal 2nd order, normalized, stable Peak Filter centered at fo 1000Hz. Use only two conjugate poles and two zeros at the origin. The system is to be sampled at Fs- 8000Hz. The duration of the transient should be as close as possible to teft 7.5 ms. The transient is assumed to end when the largest pole elevated...
P5.6-3 displays the pole-zero plot of a system that has re 5.6-5 Figure second-order real, causal LTID s Figure P5.6-5 (a) Determine the five constants k, bi, b2, aj, and a2 that specify the transfer function (b) Using the techniques of Sec. 5.6, accurately hand-sketch the system magnitude response lH[eill over the range (-π π) (c) A signal x(t) = cos(2πft) is sampled at a rate Fs 1 kHz and then input into the above LTID system to produce DT...
show all calculations
0.5 a) Hz(2) is a type-3 GLP filter and it has a zero at Z - j. Find Hz(Z) b) Convert Hz(2) to Hz(es) then calculate Hz (e)and H, (e- c) What is the relationship between the results of part (a) and part(b)? 0.6 Hap(Z) is a real all-pass filter and it has a pole at Z = + and another pole at Za bmZ- MM M Construct Hap(Z) as one block and without fractions, i.e. H(Z)...
(a) A system has the impulse response, h[n], and is excited with the input signal, xIn], as shown below. Using either a mathematical or a graphical convolution technique, determine the output of the system, y[n] (that is, evaluate y[n] h[nl'xIn], where" denotes convolution). 17 marks xIn INPUT FIR filter 0.5 0.25 OUTPUT 0 1 345 6 7 .. 0.5 0123 4567 (b) An IIR filter is shown below: ylnl One sample delay (z) 0.4 i) Derive the difference equation describing...
The Nyquist plot of a plant P in a unity feedback system is
shown below. It is know that P has one pole with a non-negative
real part.
6.13 The Nyquist plot of a plant P in a unity feedback system is shown below. It is known that P has one pole with non-negative real part 1. What is the number of poles of P with zero real part? 2. What is the number of unstable poles of P? 3....