do not forget to answer the true and false please. Required Information NOTE: This is a...
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The Howe bridge truss shown is subjected to the given loading. It is discovered that the material out of which some of the members of the truss are made might not be strong enough to support the forces acting on them. The main members in question are members HD, CD, and GD of the truss. It is desired to determine...
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part Consider the figure shown. Assume P 18 kN. I1m 2 im 4 m Draw the free-body diagram needed to determine the force in member GJof the truss shown. (You must provide an answer b moving on to the next part.) The free-body diagram needed to determine the force in member GJ of the truss is
2 part problem, thanks! Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part The pin at Bis attached to member ABD and can slide freely along the slot cut in the fixed plate. The angular velocity of arm DE is 3.5 rad/s clockwise at the instant shown. 200 mn 120 mm 30 160 am Determine the angular velocity of member ABD. (You must provide an answer before...
Write the MATLAB code and use the function linsolve() to solve the system of linear equations. Thank you! l Truss A truss is a structure that typically consists of 1. All straight members 2. connected together with pin joints 3. connected only at the ends of the members 4. and all external forces (loads&reactions) must be applied only at the joints. The weights of the members may be neglected. The basic building block of a truss is a triangle. Large...
Required information NOTE: This is a multi-part question. Once an answer is submitted, you ll be unable to return to this part A 1-kg collar can slide on a horizontal rod, which is free to rotate about a vertical shaft. The collar is initially held at A by a cord attached to the shaft. A spring of constant 30 N/m is attached to the collar and to the shaft and is undeformed when the collar is at A As the...
Step-by-step please thank you Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part Two cables tied together at C are loaded as shown. Given: Q 170 lb. 30° 4 Q. Determine the range of values of Pfor which both cables remain taut.
5 Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Bars AB and BE, each of mass 5 kg, are welded together and are pin-connected to two links AC and BD. Part 1 of 3 points 30° 0.5 m eBook 0.5 m Hint 30° Print References Draw the free-body diagram needed to determine the acceleration of the assembly and the force in links. (You must provide an...
Hi could u be more clearly when u solve the question please and thanks for helping 5:53 PM unilearn.southwales.ac.uk 3 4G 2018 2019 NG2S230_EX1Mock Paper PartA (7 marks) (25 marks) Question 2 A small footpath bridge will be built over a segment of the river Taff. The bridge will span 15 metres. When testing the bridge, two loads of 150 kN were placed on it. One at 2 metres from the left support and another 3 m from the right...
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The water in a large lake is to be used to generate electricity by the installation of a hydraulic turbine-generator at a location where the depth of the water is 57 m. Water is to be supplied at a rate of 5000 kg/s. If the electric power generated is measured to be 1862 kW and the generator efficiency...
PLEASE PLEASE BE SURE THE ANSWER IS RIGHT, THANKS Required information For a bolted assembly with eight bolts, the stiffness of each bolt is kb = 1 MN/mm and the stiffness of the members is km = 2.8 MN/mm per bolt. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly. Assume the external load is equally distributed to all the bolts. It has been determined to use M6 * 1 class 5.8 bolts with rolled...