The assembly consists of two red brass C83400 copper rods and of diameter 30 , a stainless 304 steel alloy rod of diameter 40 , and a rigid cap . The supports at , and are rigid.
Modul of elasticy for the copper is
(a) Determine the average normal stress developed in the rod .
(b) Determine the average normal stress developed in the rod .
We need at least 10 more requests to produce the answer.
0 / 10 have requested this problem solution
The more requests, the faster the answer.
The assembly consists of two red brass C83400 copper rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rod EF of diameter 40 mm, and a rigid cap G. The supports at A, C and F are rigid.
a and b The assembly consists of two red brass C83400 copper rods AB and CD of diameter 30 mm a stainless 304 steel alloy rod EF of diameter 40 mm and a rigid cap G. The supports at A, C and F are rigid ▼ Part A Determine the average normal stress developed in the rod AB Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 Value Units ƠAB : --300 mm...
Review The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF, and a rig d bar G. The modulus of elasticity for red brass C83400 is 101 GPa, for 304 stainless steel 193 GPa. (Figure 1) Part A If the horizontal displacement of end F of rod EF is 0.46 mm, determine the magnitude of P. Express your answer to three significant figures and include the appropriate...
can you please do problems 4 and 5 Problem 4 The assembly consists of two 10-mm diameter red brass C83400 copper rods AB and CD, a 15-mm diameter 304 stainless steel rod EF and a rigid bar G. If the horizontal displacement of end F of rod EF is 0.45 mm, determine the magnitude of P. 300 mm 450 mm IP Problem5 The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 14 mm2...
1. An axial structure consists of a tubular shell AB perfectly bonded to length AB of a continuous solid rod that extends from A to C, as shown. A concentrated load of 175 kN is applied to the free end C of the rod in the direction shown The shell is made of 304 stainless steel and has an outer diameter of 35 mm and an inner diameter of 25 mm. The core is made of a copper alloy known...
The assembly shown in the figure below consists of solid AB, BC and CD rods connected together, the solid rod AB has 10 mm diameter and 100 mm length, the solid rod BC has 20 mm diameter a 120 mm length, while the solid rod CD has 10 mm diameter and 100 mm length. Allh rods are made of steel with E-200 GPa. the assembly is subjected to 100 kN tensile force (CLO5) The average normal stress between A and...
A steel rod whose diameter is equal to 15 mm is held between rigid walls with no initial stress, see 2(a). The steel properties are ? = 12 × 10?6/ oC and E = 200 GPa. (a) What is the temperature drop ?T (in degrees Celsius) at which the average shear stress in the 12-mm diameter bolt becomes 55 MPa. (b) At the temperature that you defined in (a), what is the normal stress in the rod? (c) What are...
A temporary support steel frame (E 200 GPa) is made of 30-mm diameter solid circular steel rods (members AB and CD), and 22-mm diameter solid circular steel rods (members BC and AD), al pin connected at the turnbuckle corners A, B, C, and D (see Figure below). The steel frame is braced by two cables AC and BD. A turnbuckle is fitted to cable AC and tightening it will induce tension 3m in cable AC. Determine the largest allowable tension...
Figure Q1 The jib crane is pinned at A and supports a chain hoist that can travel along the bottom flange of the a) the force in rod BC b) the minimum diameter of rod BC (to the nearest 5 mm). c) the minimum diameter of pin B (to the nearest 5 mm). The material properties are listed in Table Q2 and use factor of safety of FS-2 (10 marks) beam boist Figure Q2 Table Q2: Material properties (MPa) Shear...
Due to the operational conditions and temperature gradient, a 95 mm diameter, 1.75 m long steel rod within a machine assembly is subjected to a combination of tensile loading of 190 N and thermal loading which imposes a longitudinal force of 244 N. The total loading results in an even distribution of forces on the body of the rod causing it to change its dimensions by increasing 0.45 mm in length at both ends and decreasing by 0.0135 mm at...
Due to the operational conditions and temperature gradient, a 95 mm diameter, 1.75 m long steel rod within a machine assembly is subjected to a combination of tensile loading of 190 N and thermal loading which imposes a longitudinal force of 244 N. The total loading results in an even distribution of forces on the body of the rod causing it to change its dimensions by increasing 0.45 mm in length at both ends and decreasing by 0.0135 mm at...