Problem 5-14 The conveyor belt shown a or the belt is L 20 ft. (a) Determine...
EM 216 Final Problem 5 Sand is discharged from a conveyor belt and falls onto a stockpile at B. For the dimensions shown, determine the initial velocity V, of the belt. 17 ft
Fluid Mechanics Fluid Mechanics 5. (20 points) A horizontal conveyor belt moving at 3 m/s receives sand from a container. The sand falls vertically from the container to the belt at a speed of 1.5 m/s and a flow rate of 200 kg/s. The conveyor belt is initially empty but begins to fill with sand. If the friction in the drive system and rollers is negligible. find the force required to pull the belt while the conveyor is filling. sand...
PROBLEM 13.13 20 ft ( OOOO Boxes are transported by a conveyor belt with a velocity v, to a fixed incline at A where they slide and eventually fall off at B. Knowing that m=0.40, determine the velocity of the conveyor belt if the boxes leave the incline at B with a velocity of 8 ft/s. 15
hopper drops gravel at a rate of 80.0 kg/s onto a conveyor belt that moves at a constant speed v 1.80 m/s. Determine the additional force (over and above internal friction) needed to keep the conveyor belt moving as gravel falls on it a. 80.0 N b. 144.0 N 44.4 N d)784.0 N e. 436.0 N f. None of the above. The correct answer is
A hucket drops sand vertically onto a moving conveyor-belt at the rate of 5.70 kgis. The rubber conveyor-belt is supported by wheels (frictionless) and moves at a constant speed of tha motor that drivas the belt. - D.710 m/s under the action of a constant horizontal axternal force supplied by Figure P9.87 (a) Find the sands rate of change of momentum in the horizontal direction. (b) Find the force ot friction exerted by the belt on the sand (c) Find...
Four 5.8-kg packages are placed as shown on a conveyor belt which is disengaged from its drive motor. Package 1 is just to the right of the horizontal portion of the belt. If the system is released from rest, determine the velocities of packages 1and 2 as they fall off the belt at point A. Assume that the mass of the belt and the rollers is small compared with the mass of the packages and that there is no slipping...
Problem 2: (Problem 3.79 in the book) A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with the belt tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side. (a) Determine the tensions in the belt on pulley B, assuming the...
find v belt drive design power select belt type determine shive size (belt speed 4000 ft/min) find shive size from power rating figure find rated power find estimated centre distance find belt length (by selecting standard belt length) calculate actual centre distance find contact angle for small shieve determine correct factors calculate correct power per belt no. of belt needed V-Belt Designing Sample Problem . Given: A 4 cylinder diesel engine runs at 80 hp, 1800 rpm, to drive a...
need help asap please Question 5-6 Marks A motor runs a pump via a system as shown below. Determine the following The maximum power if one V-belt is used a) The maximum power if 2 V-belts identical to the V-belt in a) are used b) The maximum power if one V-belt with twice the cross sectional area as in a) is used c) Mots The conditions of the system are as follows: Pulley radius = 120 mm =160° f =...
Problem 1 (50 points) A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a motor through a belt with tensions shown. The power is transmitted through the shaft and delivered to the belt on pulley B. Assume the belt tension on the loose side at B is 15 percent of the tension on the tight side. 230 mm F: 30-mm dia. 280 mm 300 mm 250-mm dia. 400-mm dia 1000 N 150 N...