(4.7) Consider a stepped to torsion bar of length L Li + L2 subjected to a...

Question

Question

(4.7) Consider a stepped to torsion bar of length L Li + L2 subjected to a single torqu es T. G.J GJ 2 Ti 2 し2

Answer 1

Answer #1

7 C. TAR-LA TL toc

Answer 2

Similar Homework Help Questions

4) A four-bar mechanism with Li-2 in, L2-8 in, L 4 in, find the range of...

4) A four-bar mechanism with Li-2 in, L2-8 in, L 4 in, find the range of Lo for the mechanism to act as crank-rocker mechanism
L2 B r3 L1 T 12 r Consider the torsion spring above. The shafts have shear...

L2 B r3 L1 T 12 r Consider the torsion spring above. The shafts have shear moduli of Gen- ?? ksi, GAn 15,000 ksi, and consists of a solid inner shaft CB which is surrounded by and attached to a tube AB using a rigid ring at B. The ring at A can also be assumed rigid and is fixed from rotating. The geometry is given as r, 0.50 in, r, 1.0 in, r-0.8 in, and L, 12 in and...
A bar ABCD with varying cross section and subjected to axial loads is shown schematically in...

A bar ABCD with varying cross section and subjected to axial loads is shown schematically in Figure Q3. Take modulus of elasticity of bar as 202 GPa. The length of each section L1 = 111 mm; L2 = 205 mm; and L3 = 451 mm. The cross sectional dimensions are as follows: Section 1 is square with side 49 mm, Section 2 is circular with diameter 79 mm and Section 3 is circular with diameter 32 mm. The forces are...

Consider a uniform bar of length L having an initial temperature distribution given by f(x), 0...

Consider a uniform bar of length L having an initial temperature distribution given by f(x), 0 < x < L. Assume that the temperature at the end x=0 is held at 0°C, while the end x=L is thermally insulated. Heat is lost from the lateral surface of the bar into a surrounding medium. The temperature u(x, t) satisfies the following partial differential equation and boundary conditions aluxx – Bu = Ut, 0<x<l, t> 0 u(0,t) = 0, uz (L, t)...
A solid steel bar of circular cross section has diameter d = 40 mm, length L...

A solid steel bar of circular cross section has diameter d = 40 mm, length L = 1.3 m and shear modulus of elasticity G = 80 GPa. The bar is subjected to torques T acting at the ends. If the torques have magnitude T = 340 Nm, what is the maximum shear stress in the bar? What is the angle of twist between the ends? If the allowable shear stress is 42 MPa and the allowable angle of twist...
In the figure, a bar of length L is attached by a frictionless hinge to a...

In the figure, a bar of length L is attached by a frictionless hinge to a wall and held horizontal by a rope that makes an angle with the bar. The bar is uniform and has weight W. A mass of weight Wis suspended a distance x from the hinge. If the tension T in the rope equals 2W, x must be equal to: (Hint: use torques) T L O OL(sin 0-1) OL OL(2sin - 2)

Consider the following beam subjected to a load P 18 kN and having a length L=4m.

Consider the following beam subjected to a load P 18 kN and having a length L=4m. The equation of the internal bending moment M at a random position between AB yields Determine the absolute value of the deflection at location B. in mm. Use 2-decimal places precision. Do not write the unit.
USE ANSYS (no hand calculations) Table-l: Deflection at various points along the length of the bar...

USE ANSYS (no hand calculations) Table-l: Deflection at various points along the length of the bar using 2, 4 and 8 elements and compare results with exact solution Nodal Deflection, in Finite Element Method (using Direct Method) Node # y(in) Exact Method/Analytical Solution 2-Elements 4-Elements 8-Elements 0.00 2 1.25 3 2.50 4 3.75 5 5.00 6 6.25 7 7.50 8 8.75 9 10.00 Solve example Problem # 1.1 of your book using Direct Method for 2, 4 and 8 elements...
Figure < 1 of 1 Consider, for instance, a bar of initial length L and cross-sectional...

Figure < 1 of 1 Consider, for instance, a bar of initial length L and cross-sectional area A stressed by a force of magnitude F. As a result, the bar stretches by AL (Figure 1) Let us define two new terms: • Tensile stress is the ratio of the stretching force to the cross-sectional area: stress = 5 • Tensile strain is the ratio of the elongation of the rod to the initial length of the bar strain= 41 It...

1. Consider a bar under tension. The bar has length L, rectangular cross-section of sides b...

1. Consider a bar under tension. The bar has length L, rectangular cross-section of sides b and h, Young's modulus E, density p, and applied tensile force P. a) If all parameters are fixed except for h, find the value of h that minimizes the mass of the bar under stress, elongation, and stiffness constraints. Assume safety factors oo, Os, and Ok and failure values o*, 8*, and k* b) Also find the minimum mass of the bar m under...