5. For the nameplate data above (question #4) calculate: • Slip speed = • Rotation frequency...
2). Using Mesh analysis, Calculate the current through resistor R5. R2=2022 R1=102 R3=302 R4=402 V1=60V R6=6022 R5=502 15A R7=702 R8=802 { V240V R9=902 R10=1002
electrical circuit
2). Using Mesh analysis, Calculate the current through resistor R5. R2=2022 R1=102 R3=30 12 R4=4022 V1=60V R6=6022 R5=502 15A R7=702 R8=80 V2-40V R9=902 R10=1002
Calculate the equivalent resistance Rab of the circuit shown. The resistorvalues are: R1 = 7 ohms, R2 = 4ohms,R3 = 13 ohms, R4 = 20 ohms, R5 =50 ohms, R6 = 10 ohms, R7 = 25 ohms,R8 = 22 ohms,R9 = 5 ohms, R10 =15 ohms and R11 = 5 ohms.
calculate the reliability of the following system (to 5 decimal
places):
Given R1=0.9451, R2=0.8407, R3==0.8407, R4=0.8407, R5=0.9447,
R6=0.989, R7=0.989, and R8=0.9099
6 5 3 4
units for resistance are in the picture
Part 1: Theoretical Applications of KVL, KCL, Superposition and Source Transformation Figure 1 F1 GAIN 4 R10 R2 R1 R3 R11 R8 3k R15 Wr 12 W 3k 10k 10k 2 10k V1 R9 R6 R7 12V V2 R4 RS 2k 3k R14 24Vd 3k 2k 4k 10k R13 Mr 1 R12 4k 3mAdc Figure 1 Contains three independent source and a current dependent current source (F1) 1. along with an extensive network...
Draw the pipeline diagram with data dependency considered
Appendix A Pipelining: Basic and Intermediate Concepts Data hazards occur when the pipeline changes the order of read/write accesses to operands so that the order differs from the order seen by sequentially executing instructions on an unpipelined processor. Consider the pipelined execution of these instructions: DADD DSUB AND OR XOR R1,R2,R3 R4, R1,R5 R6, R1,R7 R8, R1,R9 R10,R1,R11 All the instructions after the DADD use the result of the DADD instruction. As...
LSL R3, R3, R12 Memory Address Orig. Data Updated Data Register Orig. Data Updated Data 0x84F0 0x82 R0 0xDC002B45 0x84F1 0x32 R1 0x00008500 0x84F2 0xBC R2 0xAB03873C 0x84F3 0xA4 R3 0x2B78DFE0 0x84F4 0xF4 R4 0x000084F0 0x84F5 0x6A R5 0x00100000 0x84F6 0x9D R6 0x041B0C0D 0x84F7 0xC2 R7 0x00100000 0x84F8 0x42 R8 0x00000000 0x84F9 0x67 R9 0x00842AB0 0x84FA 0x8D R10 0x0ABD9830 0x84FB 0xA1 R11 0x0000000A 0x84FC 0xF2 R12 0x00000002 0x84FD 0xB8 R13 0X00008500 0x84FE 0x5E R14 0x003762DD 0x84FF 0xEE R15 0x00100000 0x8500...
CHAPTER 4: CONTINUE ll. Multicast Routing Consider the network topology in Figure-2 below H1 NET- Router R1 R3 R2 R10 R4 R5 R6 R7 R8 R9 NET-4 NET-3 NET-2 H3 H5 H4 Figure 2: Multicast/Broadcast Topology CHAPTER 4: CONTINUE I. Multicast Routing - Continue Q3. Assume the host H1 is willing to multicast a message to the hosts H3, H4, and H5. Assume a center-based tree approach is used for multicast, R5 is selected as the center, and number-of-hops is...
RESISTOR VALUES: R1=1k, R2=2k, R3=3k, R4=3.9k, R5=5.1k, R6=6.2k,
R7=6.8K
NUMBERS: 2, 4, & 5
1 Short AB, as shown in Figure 3 - 2 (a). Use mesh analysis to calculate the voltage across each resistor and the current through AB, IAB 2. Leave AB open, as shown in Figure 3 - 2 (b). Use nodal analysis to calculate the voltage across each resistor as well as the voltage across AB, VAB 3. Find Thevenin's and Norton's Equivalent using the results...
Consider a VEX-executing VLIW machine with the following characteristics: The machine supports 4 slots (4-wide machine) with the following resources: 2 memory units each with a load latency of 3 cycles 2 integer-add/sub functional units with a latency of 2 cycle 1 integer-multiply functional unit with a latency of 4 cycles Each functional unit in the machine is pipelined and can be issued a new operation at each cycle. However, the results of an operation are only available after the...