3. Design an op amp circuit using one op amp that will take two inputs, Vi...

Question

Question

3. Design an op amp circuit using one op amp that will take two inputs, Vi and V2, and produce an output Vo--4V1 - 2V2.

Answer 1

Answer #1

S0 his can e achived as hnou S 나 1.C ov 6-Vo R. 尺 2

Answer 2

Similar Homework Help Questions

sing one op-amp (or op-amps) und kilo-Ohm resistors, design a circuit to om the operation with...

sing one op-amp (or op-amps) und kilo-Ohm resistors, design a circuit to om the operation with two inputs and one output). Assume ideal op-amps (an 12 volt power supplies). vo - 5(v12 - Vil)
1- Design a lossy integrator op-amp circuit using op-amp 741. First, derive an expression for - V...

UPLOAD PSPICE SIMULATION TO VERIFY CALCULATIONS 1- Design a lossy integrator op-amp circuit using op-amp 741. First, derive an expression for - Vo Then assign values to circuit components in order to have Gai 1. Verify your design with a PSpice simulation. Since gain value depends on Vi frequency, perform an AC sweep analysis (frequency response) to obtain which frequency gives you this gain. Report this trequency. IVil 1- Design a lossy integrator op-amp circuit using op-amp 741. First, derive...
For the Op Amp circuit shown, if the inputs v1 = 5 volts, and v2 = 3 volts

For the Op Amp circuit shown, if the inputs v1 = 5 volts, and v2 = 3 volts, and resistances R1 = R2 =10 KΩ and RF = 5kΩ , then the output out will be _______ volts. This circuit is called a _______ OP Amp circuit. The name indicates the application of the circuit. The Op Amp provides _______ output impedance.

Design an Op Amp Circuit for the following equation. Hint: Keep in mind there are TWO...

Design an Op Amp Circuit for the following equation. Hint: Keep in mind there are TWO inputs (V1 and V2) and make sure you account for the the minus signs of Op Amps.
Problem 2: In the circuit shown assume the Op-Amp is ideal. A) Find vo as a...

Problem 2: In the circuit shown assume the Op-Amp is ideal. A) Find vo as a function of vi and vs. B) Next assume the Op-Amp is ideal, except its low frequency gain is Ao= 100 V/V. Now find vo as a function of vi and v2. C) The Op-Amp has a terminal frequency of fi 10° Hz, find the -3 dB (corner) frequency of the output signal w2 10K
Problem 7 (CLO 3, 4, 11 - Ideal Op-Amps, Design): We will now design an Op-Amp...

Problem 7 (CLO 3, 4, 11 - Ideal Op-Amps, Design): We will now design an Op-Amp circuit to perform the function where v1 - input voltage 1, input voltage 2, = input voltage 3, Vo = output voltage. It may be helpful to consult your recitation 6 (week 7) results as well as Table 4-3 for this problem. 7.a: Select an Op-Amp configuration for your design. Sketch the Op-Amp configuration with symbolic resistors (Rf, Ri, R2, etc) indicated. Do not...

Using only one op-amp, design an amplifier that will have the following output:

Using only one op-amp, design an amplifier that will have the following output: Vo = 16 (Vi2 - Vi1)
Q16. Design a two-stage Op-Amp circuit as shown below to make the output voltage is v,-CV1-c2v2,...

Q16. Design a two-stage Op-Amp circuit as shown below to make the output voltage is v,-CV1-c2v2, where C1 = 7.5 and C2 = 7.5, given that Rf,-73 kQ, and Rn° 18 ka. Rf, Ri 0 %, 0 R, Rs2 V Vi 0 O Vo v2 P2 Stage Stage 2 16a. Find the values of R and R2 R1: 4.056 Submit Answer Incorrect. Tries 1/3 Previous Tries (k2) R2 1 (k2) 16b. Find the value of Rs2 (k2) Submit Answer Incorrect....
ECE 202- Experiment 3-PreLab Homework NTROD TION TOTHE INTEG IRO T OP AMP VOLTAGE COMPARATOR 1....

ECE 202- Experiment 3-PreLab Homework NTROD TION TOTHE INTEG IRO T OP AMP VOLTAGE COMPARATOR 1. Op Amp functions in two different modes, depending on the way it is connected in the circuit a) If there is no return loop, t is used to compare values of two input terminals (or as Explain how vo changes depending on the values of vi and v Vo . what are max and/or min values for v and vo? 2·The circuit shown below...

pts) Consider the following Op Amp Circuit, use Op Amp rules to calculate vo vi and...

pts) Consider the following Op Amp Circuit, use Op Amp rules to calculate vo vi and vx vi . hint: you may need to introduce a variable Vx in your KCL equations. Use R1 = 1Ω, R2 = R3 = R4 = 2kΩ, Rf = 3kΩ. 1. (40 pts) Consider the following Op Amp Circuit, use Op Amp rules to calculated and hint: you may need to introduce a variable Vx in your KCL equations. Use R1 = 12, R2...