given the signal energy per bit and the noise PSD to find the SNR/bit..(give an example)
given the signal energy per bit and the noise PSD to find the SNR/bit..(give an example)
3. The quality of a received signal is often characterized by the signal-to-noise-ratio (SNR), which is defined as SNR 10 log As you might expect from this Signal power in watts KTB definition, the unit of SNR is decibels (dB). The term in the denominator is the noise power, and it is generally specified as an effective noise temperature T multiplied by the product of Boltzmann's constant (K) and the bandwidth (B) of the signal in Hz. Generally we like...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandwidth 5 kHz, the receiver output SNR is required to be at least 47 dB. The receiver is as shown in Fig. 8.30. (a) What must be the signal power Si received at the receiver input? (b) What is the receiver output noise power No? (c) What is the minimum transmitted power Sr if the channel transfer function is He)10-3 over...
4. (8 points) A noise signal ni(t) with power spectrum density (PSD) S () = k ) is applied at the input of an deal differentiator. Determine the PSD and the power of the output noise signal no(t) (hint: no(t) = 0).
Q.2 ICO2]10 Marks] The signal g(t) forms the input to the LPF circuit shown in the figure, where R l,and y(Dis the output. If the power spectral density (PSD) of the signal ge) is (a) The autocorrelation of g(t) (b) The 3-dB bandwidth of the LPF (c) The power of g(t) and y(t) (d) Based on your answers above, will it be better if the signal has more or less bandwith? (e) If a white noise of PSD No/2 is...
Consider additive white Gaussian noise with a double-sided noise power spectral density (PSD) 12-90 dBm/Hz 1E-12 W/Hz. This noise corrupts a baseband polar NRZ signal with rectangular pulses, like that 1 mV and the pulse duration is Tb such that the symbol rate is Rb 1/Tb. Since this is binary signaling, the symbol rate equals the bit rate of the incoming baseband pulse train: B Rt. The signal is then sampled at the center of the noisy shown in the...
2. 12 pts] An FM system has a modulation index β-6 aid the input signal-to-noise ratio SNR 25dB. The message is a periodic square wave given in the figure below pulse width -0.2m 2 0 0 t (ms) a) What is the output SNR.? b) What is the proper value of the message bandwidth? [Justify your answer. c) What is the corresponding FM transmission bandwidth? d) If the modulation index is kept at β 6, what should be the increase...
Given a signal to a radio receiver consists of 200uV of signal power and 2 uW of noise power. If the receiver contributes an additional 160 W of noise, NR, and has a power gain of 20 dB. ) Calculate the input SNR, (ii) the output SNR and (iii) the receiver's NE
Given a message signal m(t) with a bandwidth of 4kHz and a Power of 1W, find the post-detection SNR (Signal-to-noise Ratio) in [dB], of the Amplitude Modulated Signal: s(t) = 10*(1+0.5*m(t))cos(
Calculate SNR(dB) given a noise voltage specification of 500.5nV/sqrt(Hz), used over an audio frequency range of 20Hz to 20kHz, with a voltage gain of 55dB. The output voltage is 1.75 V. Calculate the noise voltage specification given SNR(dB) = 150dB using the same output voltage, frequency range, and gain as in number 3.
Problem 4: For a digital baseband modulated signal with bit duration of 1 ms, the signal was line coded using Polar bit mapping and NRZ baseband pulse shape. Find the power contained in its PSD at f 1 kHz.