i have tried posting 5 times Already and every answer has been incorrect. Please help me get this right I only get one chance before it changes the question
Homework Answers
Add Answer to:
i have tried posting 5 times Already and every answer has been
incorrect. Please help me...
can someone please help me with this question. I've tried to solve it but I seem...
can someone please help me with this question. I've
tried to solve it but I seem to get nowhere.
A chopper is used in the regenerative braking of a dc series motor similar to the arrangement shown in Figure Q2. The armature resistance R = 0.02 and the field resistance Rp=0.032. The armature current is maintained at a constant value of la = 200 A The back emf constant Ko = 15.25 mV/A rad s. The dc supply voltage Vs...
Can someone answer Q5 for me please?? And how do I measure Z? 5. How does...
Can someone answer Q5 for me please??
And how do I measure Z?
5. How does the location of the current peak compare to the location of the voltage peak in each plot at 10 Hz? (Consider where the peaks occur in time) Reset Run / STOP 2uF Simulation Speed Current Speed 0 Power Brightness Current Circuit: 10Hz 1k New X S -15.933 V 100.165 ms 167.681 V capacitor, 2 UF 21.071 V resistor, 1 ko 169 V A/C source...
Can I get help with part g through part r, please? Given the following Common-Emitter Amplifier...
Can I get help with part g through part r, please?
Given the following Common-Emitter Amplifier with Voltage-Divider Bias: The transistor is a Silicon device with B160 (Beta 160) and transistor r.= 30 kn: 20 V 34.7k LAL = Vou 35.10 31.1k LRE $3900 03 - Find the following quantities in parts a through where means Quiescent DC): a) Thevenin Voltage and Thevenin Resistance Re b) Base Current la Collector Current le d) Emitter Current le e) Transistor Collector-Emitter Quiescent...
Could you please show me how I can drw those circuits. please using (NI Multisim 14)...
Could you please show me how I can drw those circuits.
please using (NI Multisim 14)
Optocoupler Objectives Use an ohmmeter to determine the condition of the optoisolator. Observe the operation of an optocoupler. Determine the maximum frequency response of the optocoupler. Required Materials (1) Dual DC power supply (1) Function generator (1) Oscilloscope (2) Multimeters (1) Optocoupler (ECG3040) (1) 3.9ΚΩ resistor (1) 220 resistor Introduction An optoisolator is a hybrid integrated circuit that contains an LED on one side...
can someone please help me with this question. I've
tried to solve it but I seem to get nowhere.
A chopper is used in the regenerative braking of a dc series motor similar to the arrangement shown in Figure Q2. The armature resistance R = 0.02 and the field resistance Rp=0.032. The armature current is maintained at a constant value of la = 200 A The back emf constant Ko = 15.25 mV/A rad s. The dc supply voltage Vs...
Can someone answer Q5 for me please??
And how do I measure Z?
5. How does the location of the current peak compare to the location of the voltage peak in each plot at 10 Hz? (Consider where the peaks occur in time) Reset Run / STOP 2uF Simulation Speed Current Speed 0 Power Brightness Current Circuit: 10Hz 1k New X S -15.933 V 100.165 ms 167.681 V capacitor, 2 UF 21.071 V resistor, 1 ko 169 V A/C source...
Can I get help with part g through part r, please?
Given the following Common-Emitter Amplifier with Voltage-Divider Bias: The transistor is a Silicon device with B160 (Beta 160) and transistor r.= 30 kn: 20 V 34.7k LAL = Vou 35.10 31.1k LRE $3900 03 - Find the following quantities in parts a through where means Quiescent DC): a) Thevenin Voltage and Thevenin Resistance Re b) Base Current la Collector Current le d) Emitter Current le e) Transistor Collector-Emitter Quiescent...
Could you please show me how I can drw those circuits.
please using (NI Multisim 14)
Optocoupler Objectives Use an ohmmeter to determine the condition of the optoisolator. Observe the operation of an optocoupler. Determine the maximum frequency response of the optocoupler. Required Materials (1) Dual DC power supply (1) Function generator (1) Oscilloscope (2) Multimeters (1) Optocoupler (ECG3040) (1) 3.9ΚΩ resistor (1) 220 resistor Introduction An optoisolator is a hybrid integrated circuit that contains an LED on one side...
Most questions answered within 3 hours.
-
A 0.25μF capacitor is charged to 50 V . It is then connected in
series with...
asked 6 minutes ago -
Calculate the current, I, through the batteries for:
- a 2-bulb parallel circuit
- How does...
asked 7 minutes ago -
Choose the sentence that uses correct punctuation.
1a. The prefatory parts of a report include the...
asked 13 minutes ago -
For the element arsenic, which one of the following sets of
quantum numbers could not apply...
asked 22 minutes ago -
Compare and contrast the architectures of 3 types of ADCs:
Flash, SAR, and pipelined. Use the...
asked 24 minutes ago -
Given P(A) = 0.40, P(B) = 0.50, P(A ∩ B) = 0.15. Which of the
following...
asked 28 minutes ago -
Explain changes in workforce participation for women with
children. What legislation exists related to work and...
asked 30 minutes ago -
How high must a pointed arch be if it is to span a
space 4.2 m...
asked 35 minutes ago -
A housepainter who weighs 750 N stands 0.6 m from one end of a
2.0 m...
asked 37 minutes ago -
Implement Singly Linked List detectLoop in Java.
It would check whether the linked list contains a...
asked 40 minutes ago -
A small mailbag is released from a helicopter that is descending
steadily at 2.10 m/s.
After...
asked 41 minutes ago -
Write a C – program that calls a user-defined function from
within main() that determines the...
asked 44 minutes ago