Time for 1 character = 0.74ms
Time for 1024 character = 0.759s
in easy68k or 68000 6. Suppose that an MC68681 is configured to transmit and receive data...
Assume that an asynchronous serial communication protocol is configured to utilize 15-bit data, odd parity, one start bit, one and a half stop bits, and a baud rate of 100kHz. If you were to send 200,000 data frames using the aforementioned protocol, precisely how long should this take, assuming any extraneous communication overhead is negligible?
4. If an asynchronous frame is used to send ASCII characters in the form of bytes (8 bits), what is the shortest time it could take to send 1000 characters if each bit in a frame is 1 msec long? 5. Suppose an asynchronous frame holds 8 bits of data, a parity bit, and two stop bits (it could happen). Calculate the efficiency of the communication system. Suppose a synchronous frame has 16 bits of non-data in the front and...
Please explain! 15. Calculate the total number of bits transferred if 200 pages of ASCIIl data are sent using asynchronous serial data transfer. Assume a data size of 8 bits, I stop bit, and no parity. Assume each page has 80x25 of text characters. 16. In Problem 15, how long will the data transfer take if the baud rate is 9.600?
1. How many different characters could be encoded using a six-bit code? 2. What is the numerical difference between ASCI a and ASClI 'AN if you treaj them as hexadecimal (hex) numbers? 3. The ASCII codes for the characters 'O' through '9' are what hex numbers? If an asynchronous frame is used to send ASCII characters in the form of bytes (8 bits), what is the shortest time it could take to send 1000 characters if each bit in a...
1. (ch.7) A PCM/TDM system multiplexes 24 voice band channels. Each sample is encoded into 7 bits and a frame consists of one sample from each channel. A framing bit is added to each frame. The sampling rate is 9000 samples/sec. What is the line speed in bits per second? 2. (ch.9) An asynchronous protocol uses 1 start bit, 7 data bits, 2 stop bits and 1 even parity bit for each character. a. How many bits are in a...
1. Fill in the blanks to configure the SCII module of HCS12 with the following settings 14400 baud (Bus clock is 24 MHz) SCI enabled in wait mode One start bit, 8 data bits, one stop bit Enable transmit and receive Enable TDRE (TX data register empty) interrupt Enable RDRF (RX data register full) interrupt No loop back Enablc parity checking and use odd parity ; ; 14400 baud SCI enabled in wait mode; enable parity and use odd parity...
A common measure of transmission for digital data is the baud rate, defined as the number of bits transmitted per second. Generally, packet transmission consists of a start bit, a byte of information, and a stop bit. How long would it take to transmit a 5"x7" picture with a resolution of 300 pixels/inch with 256 levels per pixel and a compression ratio of 2.625 using a: 1. 2. 3. 4. 9.6K baud modem-released in 1984? 56K baud modem - released...
Suppose an 802.11b station is configured to always reserve the channel with the RTS/CTS sequence. We assume a frame without data is 35 bytes long, and the transmission rate is 10 Mbps. Suppose this station suddenly wants to transmit 500 bytes of data, and all other stations are idle at this time. As a function of SIFS and DIFS, and ignoring propagation delay and assuming no bit errors, calculate the time required to transmit the frame and receive the acknowledgement....
Wireless and Mobile Network (10 points) Suppose an 802.11b station is configured to always reserve the channel with the RTS/CTS sequence. We assume a frame without data is 35 bytes long, and the transmission rate is 10 Mbps. Suppose this station suddenly wants to transmit 500 bytes of data, and all other stations are idle at this time. As a function of SIFS and DIFS, and ignoring propagation delay and assuming no bit errors, calculate the time required to transmit...
Is the data valid? SPACE 0 0 1 0 1 1 MARK Bit Parity Stop 6 bit bit Start Bit bit 0 NRZI format for ASCI "M", 7 bits, Even Parity, 1 Stop Bit