Homework Answers
Add Answer to:
The gear transmits 680 N.mm of torque. The shaft is to be made of SAE 1040...
QUESTION 1 A portion of a shaft where gear is to be mounted has a diameter...
QUESTION 1 A portion of a shaft where gear is to be mounted has a diameter of 134 mm. The gear transmits 446 N.mm of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel. The key is made from SAE 1018 steel (Sy: 372 MPa; Su: 441 MPa) The width of the hub of the gear mounted at this location is 10 mm. Compute the Shearing force...
A portion of a shaft where a gear is to be mounted has diameter of 50...
A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...
A 6061-T6 aluminum pulley transmits 75 hp at 1,750 rpm. The shaft is 1% inches in diameter and is...
A 6061-T6 aluminum pulley transmits 75 hp at 1,750 rpm. The shaft is 1% inches in diameter and is made from cold-drawn 1040 steel. The key is to be made from cold-drawn 1020 steel. For a safety fac- tor of 3, compute the required square key length for both shear and compression
A 6061-T6 aluminum pulley transmits 75 hp at 1,750 rpm. The shaft is 1% inches in diameter and is made from cold-drawn 1040 steel. The key is to...
4.) A gear with a pitch diameter of 10in and pressure angle of 20 degrees delivers 150hp at 500rp...
4.) A gear with a pitch diameter of 10in and pressure angle of 20 degrees delivers 150hp at 500rpm to its shaft. The shaft is made of SAE 1144 OQT 1000 steel a. What torque is delivered to the shaft? (5 points) b. What is the basic endurance strength for a machined shaft of SAE 1144 OQT C. What is the stress concentration factor for a profile keyseat? (5 points) d. The bending moments for a gear using a profile...
QUESTION 9 A line shaft rotating at speed to transmit power through torque equal to 911...
QUESTION 9 A line shaft rotating at speed to transmit power through torque equal to 911 N.m. The shaft is made of mild steel with an allowable shear stress of 68 MPa. Neglecting the effect of bending moment on the shaft. Compute the diameter of the shaft (mm)? QUESTION 11 A gear carried by a shaft exerts a force on the shaft. The torque transmitted by the gear is equal to 377,890 N.mm. The Pitch diameter of the gear is...
QUESTION 1 A shaft where a pulley is to be mounted has a diameter of 82...
QUESTION 1 A shaft where a pulley is to be mounted has a diameter of 82 mm. The pulley transmits a torque of 714 N.m. The shaft is to be made of SAE 4140 alloy steel. The pulley is made from 1095 Carbon steel. The width of the hub of the pulley mounted at this location is 25 mm. The design factor is 5, and pulley rotates at 650 rpm. Sy for Shaft material: 621 MPa Sy for Pulley material:...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20". The shaft transmits a torque to point A of TA = 340 N.m. The shaft is machined from steel with Sy= 420 MPa and Sut = 560 MPa. The fatigue...
QUESTION 1 It is required to design a square key for fixing a gear on a...
QUESTION 1 It is required to design a square key for fixing a gear on a shaft of 27 mm diameter. The shaft is transmitting torque of 195,844 N.mm to the gear. The width of the key is equal 7 mm. The key is made of steel 50C4 (sy - 577 N/mm2) and the factor of safety is 3. For key material, the yield strength in compression can be assumed to be equal to the yield strength in tension. Determine...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power a...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
The rotating solid steel shaft is simply supported by bearings at points B and C and...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
QUESTION 1 A portion of a shaft where gear is to be mounted has a diameter of 134 mm. The gear transmits 446 N.mm of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel. The key is made from SAE 1018 steel (Sy: 372 MPa; Su: 441 MPa) The width of the hub of the gear mounted at this location is 10 mm. Compute the Shearing force...
A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...
A 6061-T6 aluminum pulley transmits 75 hp at 1,750 rpm. The shaft is 1% inches in diameter and is made from cold-drawn 1040 steel. The key is to be made from cold-drawn 1020 steel. For a safety fac- tor of 3, compute the required square key length for both shear and compression
A 6061-T6 aluminum pulley transmits 75 hp at 1,750 rpm. The shaft is 1% inches in diameter and is made from cold-drawn 1040 steel. The key is to...
4.) A gear with a pitch diameter of 10in and pressure angle of 20 degrees delivers 150hp at 500rpm to its shaft. The shaft is made of SAE 1144 OQT 1000 steel a. What torque is delivered to the shaft? (5 points) b. What is the basic endurance strength for a machined shaft of SAE 1144 OQT C. What is the stress concentration factor for a profile keyseat? (5 points) d. The bending moments for a gear using a profile...
QUESTION 9 A line shaft rotating at speed to transmit power through torque equal to 911 N.m. The shaft is made of mild steel with an allowable shear stress of 68 MPa. Neglecting the effect of bending moment on the shaft. Compute the diameter of the shaft (mm)? QUESTION 11 A gear carried by a shaft exerts a force on the shaft. The torque transmitted by the gear is equal to 377,890 N.mm. The Pitch diameter of the gear is...
QUESTION 1 A shaft where a pulley is to be mounted has a diameter of 82 mm. The pulley transmits a torque of 714 N.m. The shaft is to be made of SAE 4140 alloy steel. The pulley is made from 1095 Carbon steel. The width of the hub of the pulley mounted at this location is 25 mm. The design factor is 5, and pulley rotates at 650 rpm. Sy for Shaft material: 621 MPa Sy for Pulley material:...
QUESTION 1 It is required to design a square key for fixing a gear on a shaft of 27 mm diameter. The shaft is transmitting torque of 195,844 N.mm to the gear. The width of the key is equal 7 mm. The key is made of steel 50C4 (sy - 577 N/mm2) and the factor of safety is 3. For key material, the yield strength in compression can be assumed to be equal to the yield strength in tension. Determine...
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
The rotating solid steel shaft is simply supported by bearings at points B and C and is driven by a gear (not shown) which meshes with the spur gear at D, which has a 150-mm pitch diameter. The force F from the drive gear acts at a pressure angle of 20°. The shaft transmits a torque to point A of T 400 N m. The shaft is machined from steel with S, 420 MPa and Su 560 MPa. Using a...
Most questions answered within 3 hours.
-
Atmospheric Mass
Venus and Earth have about the same mass and radius, but the
atmospheric pressure...
asked 4 minutes ago -
5. Discuss the use of fault tree analysis (FTA) for risk
assessment (maximum one paragraph).
asked 1 hour ago -
Given that a sample of aluminium oxide has a Young's modulus of
393 GPa and a...
asked 2 hours ago -
At a certain temperature, the equilibrium constant, Kc, for this
reaction is 53.3.
H2(g)+I2(g)−⇀↽−2HI(g)Kc=53.3
At this...
asked 4 hours ago -
Question1 ) The STL provides similiar classes called stack and
queue, both of which gave functions...
asked 5 hours ago -
For Questions 1-4, assume you have 5 bits available:
1. For (positive) integers: What is the...
asked 5 hours ago -
convert grams into vloume with the density of water being at
.997514 g/cm^3 at 23.1 Celsuis...
asked 7 hours ago -
Foreman company obtained a $20,000, 6% loan on May 1, 2018.
Principal and interest will be...
asked 7 hours ago -
5. Problem 11.05 (Discounted Payback)
eBook
Project L costs $60,000, its expected cash inflows are $14,000
per...
asked 7 hours ago -
1. Which of the following is true about politics and health
organizations?
A. Health organizations are...
asked 8 hours ago -
A space vehicle is coasting at a constant velocity of 18.1 m/s
in the +y direction...
asked 9 hours ago -
5) Use the following balanced equation to answer questions
(a)-(i).
3 Cu(s) + 8 HNO3(aq) →...
asked 8 hours ago