Pls show work < HW Set #11 (10.7, 11, 12.1, 12.2) 4 of 10 Problem 10.89...

Question

Question

Pls show work

Answer 1

Answer #1

paincipal Sus 2 12-s , z = 2± 12.2065 . ơi- 14-2065 An KS Max Shear stoeu the Buy 45一一 )-84 Maxration eniwy the 21.24 KSİ 21.

Answer 2

Similar Homework Help Questions

Problem 10.81 The material shown in the figure below (Figure 1) has a yield strength of...

Problem 10.81 The material shown in the figure below (Figure 1) has a yield strength of Oy = 80 ksi. Figure < 1 of 1 > 12 ksi 10 ksi -20 ksi Part A Determine the factor of safety for this loading against yielding based on the maximum shear stress theory. Express your answer to three significant figures. Y A vec mo? F.S. Submit Request Answer Part B Determine the factor of safety for this loading against yielding based on...
Pls show work HW Set #1: Chapters 1 and 2 Problem 1.80 The cotter is used...

Pls show work HW Set #1: Chapters 1 and 2 Problem 1.80 The cotter is used to hold the two rods together. (Figure 1) All parts are made of steel for which the falure normal stress is Ơfall-480 MPa and the tadure shear stress is Thi 400 MPa Use a factor of safety of (F.S.),-2.30 in tension and (F.S.),-1.64 in shear Part A Determine the smallest thickness t of the cotter Express your answer to three significant figures and include...
The bracket is shown in (Figure 1). Assume that 1 = 50 mm, a = 180...

The bracket is shown in (Figure 1). Assume that 1 = 50 mm, a = 180 mm, t = 4 mm, h = 45 mm, F = 950 N, ID = 30 mm, OD = 50 mm. Assume a ductile material strength of Sy = 400 MPa (60 kpsi). Part A Calculate the safety factor at point A using the distortion-energy theory. Express your answer to three significant figures. VALOIT vec ? NDE A Submit Request Answer Figure 1 of...

<HW #6 Problem 4.72 ① 2 of 3 Review Part A The two cylindrical rod segments...

<HW #6 Problem 4.72 ① 2 of 3 Review Part A The two cylindrical rod segments shown in the figure below (Figure 1) are fixed to the rigid walls such that there is a gap of 0.01 in between them when Ti = 60°F. Each rod has a diameter of 1.25 in. Take a = 13(10-)/F, E2 = 10(103) ksi, (oyal = 40 ksi, acu = 9.4(10-/F, (OY)cu - 50 ksi, and Ecu = 15(10) ksi Determine the average normal...
<Hw 05 01 Chapter 5 10 of 11 Problem 5.48 Review I Constant Part A The...

<Hw 05 01 Chapter 5 10 of 11 Problem 5.48 Review I Constant Part A The op amp in the noninverting amplifier circuit in (Figure 1) has an input resistance of 400 kn, an output resistance of kn, and an open-loop gain of 20.000 Assume that the op amp is operating in its linear region Calculate the voltage gain (v/v). Express your answer using five significant figures. VAXDvec ? > Figure 1 of 1 Submit Becuest Answer Part 6 NON...
Homework Set #6-Chapter 6 Problem 6.87 4 of 10 > The beam has a rectangular cross...

Homework Set #6-Chapter 6 Problem 6.87 4 of 10 > The beam has a rectangular cross section with b = 8 in. 2b 6 ft Part A Determine the largest maximum intensity wo of the triangular distributed load that can be supported if the allowable bending stress is σ 1-1.7 ksi Express your answer to three significant figures. uo = Submit Provide Feedback Next >

Course Home <Column Buckling A Problem 13.18 4 of 4 A Revie: The wooden column has...

Course Home <Column Buckling A Problem 13.18 4 of 4 A Revie: The wooden column has the dimensions shown. Take that L = 11 ft (Figure 1) Part A Determine the critical load if the bottom is fixed and the top is pinned E.-17 (10) ksi oy - ksi Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 uả th P" Value Units Submit Request Answer 2 in < Return to Assignment Provide...
005-10768-201903> Assignments MP HW 02 MP HW 02 KMP HW 02 9 of 10> Problem 2.49...

005-10768-201903> Assignments MP HW 02 MP HW 02 KMP HW 02 9 of 10> Problem 2.49 ㎜ Review PartA You're driving down the highway late one night at 20 m/s when a deer steps onto the road 37 m in tront of you. Your reaction time before stepping on the brakes is 0.50 s, and the maximum deceleration of your car is 10 m/s2 How much distance is between you and the deer when you come to a stop? Express...
CHW #10 Problem 17.51 9 of 11> 9 of The pipe has a mass of 750...

CHW #10 Problem 17.51 9 of 11> 9 of The pipe has a mass of 750 kg and is being towed behind the truck. Figure 1) Part A the acceleration otte truck is ae=0.6 m/s.dmerno te the ground is μ": 02. inecati. The ooohint of krete toon ben een t, ppe and Express your answer to three significant figures and include the approprlate units T. [ Value Units ] Submit Figure 1 of1 Part B Also, determine the angle 6...

pls solve it right this time Segment A of the composite beam is made from 2014-T6...

pls solve it right this time Segment A of the composite beam is made from 2014-T6 aluminum alloy and segment B is A-36 steel The allowable bending stress for the aluminum and steel are (ơallow)al-15 ksi and (Ơallow),-22 ksi. Suppose that L-14.7 ft. (Figure 1) Part A Determine the maximum allowable intensity w of the uniform distributed load. Express your answer using three significant figures Figure 1 of 1 1.067 kip/ft Submit Incorrect; Try Again; 5 attempts remaining 3 in...