A circular rod with a diameter d- 1 in. is cantilevered at one end, and subjected...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 1201bf (downward) to F= -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress og at...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress Oa...
a A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress Om and alternating stress oa...
answer E,F,G and H please 2. A bar of steel undergoes cyclic loading such that max = 60 kpsi and Omin = -20 kpsi. For the material, Sut = 80 kpsi, 5y = 65 kpsi,ka = 1.107. ky = 0.858, ke = ka = k, = k, = 1, and f = 0.9. (a) Calculate the alternating stress. (2 points) (b) Calculate the meani median) stress. (2 points) (c) Calculate the fully corrected endurance limit. (6 points) (d) Calculate the...
A solid square rod is cantilevered at one end. The rod is 1 m long and supports a completely reversing transverse load at the other end of ±1.5 kN. The material is AISI 1080 hot-rolled steel. If the rod must support this load for 4 × 104 cycles with a design factor of 1.5, what dimension should the square cross section have? Neglect any stress concentrations at the support end. Determine the size of the cross-section.The size of the cross-section...
A beam with a square cross-section of linch X 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress og...
A beam with a square cross-section of linch x 1inch is cantilevered at one end, and subjected to a force that fluctuates from F = 120lbf (downward) to F = -600lbf (upward) at its tip. The length of beam is L = 25 inches. The selected steel material has mechanical properties as shown in the following S-N fatigue diagram. Hint: neglect any stress concentration at the support end. (a) (4 points) Calculate the midrange stress om and alternating stress Og...
5. (20 pts) A notched circular shaft shown is subjected to fully reversed bending. D-12.7mm, d-10.16 mm, and r-0.5mm. The steel material has the following mechanical and fatigue properties: yield strength (0o)-1000 MPa, ultimate strength (o ) 1200 MPa, the fatigue strength coefficient (σ) 1600 MPa, the fatigue strength exponent (b) 0.1, and the fatigue limit (oe)-400 MPa. a) (10 pts) Determine the fatigue (S-N) curve for the given notched circular shaft under fully reversed bending (computer generated graph is...
A notched circular shaft shown is subjected to fully reversed bending. D=12.7mm, d=10.16 mm, and r=0.5mm. The steel material has the following mechanical and fatigue properties: yield strength (σ0)=1000 MPa, ultimate strength (σu)=1200 MPa, the fatigue strength coefficient (σf’)=1600 MPa, the fatigue strength exponent (b)=-0.1, and the fatigue limit (σe)=400 MPa. 5. (20 pts) A notched circular shaft shown is subjected to fully reversed bending. D-12.7mm, d-10.16 mm, and r-0.5mm. The steel material has the following mechanical and fatigue properties:...
A 6.4 mm diameter cylindrical rod fabricated from a 2014-T6 aluminium alloy is subjected to reversed tension-compression load cycling along its axis of +7400 N to -2250N. Determine the fatigue life using the data shown below. 500 400 1045 steel 300 2014-T6 aluminum alloy 200 100 Red brass 10 103 104 106 105 108 10° 1010 Cycles to failure, N Stress amplitude, S (MPa) A 6.4 mm diameter cylindrical rod fabricated from a 2014-T6 aluminium alloy is subjected to reversed...