A very sharp picture with little blurring implies that the shutter speed is very fast. This is because if shutter speed is slow, then the object would have moved a bit, and the image would appear blurry.
photo grahpers control the blurring in a pocture bu barying the shitter speed i.e the amount...
Sketch root locus
camera Wobble control can be represented by the below block Diagrarm ime constant of the rate Gyro is assumed negligible i.e r10 Motor Rate Gyro Controller Bellow speed Vb km Tmst Camera speed Vc Tachometer
camera Wobble control can be represented by the below block Diagrarm ime constant of the rate Gyro is assumed negligible i.e r10 Motor Rate Gyro Controller Bellow speed Vb km Tmst Camera speed Vc Tachometer
dependent amount of weight loss (5) Suggest a control treatment for each of the following experiments: a. (1 pt.) Plants are exposed to different intensities of light and the amount of oxygen produced during photosynthesis is recorded. depend ut Ditterent intensities of light. b. (1 pt.) Frogs are captured from polluted ponds. The investigator records the number of limb deformities froy Cciplilled from Ponds. Clean c. (1 pt.) Patients taking different doses of a new medication were monitored for weight...
Problem 1: Speed versus time plot of a small DC motor is obtained when 1 Volt input is applied. The response curve is shown below: a) Approximate the open loop transfer 6 function, G(s) of the DC motor. b) A simple proportional controller (P- controller) is applied to the same DC motor. The control goal is to track a constant target speed ofr 150 rpm. Determine the control gain Kp which guarantees an offset error of e 5 rpm. (i.e.,...
3. A quality control manager at an amusement park feels that the amount of time that peopled if effective in reducing wait time, he measure the amount of time people wait in line on and then measures the amount of time after he implements the new system below. To make sure the test is fair, he measure the wait times at the same time during the 7 period and twice on Saturday and Sunday f a new loading procedure The...
6. Consider a state-space system x = Ax+ Bu, y = Cx for which the control input is defined as u- -Kx + r, with r(t) a reference input. This results in a closed-loop system x (A-BK)x(t)+ Br(t) = with matrices 2 -2 K=[k1 K2 For this type of controller, ki, k2 ER do not need to be restricted to positive numbers - any real number is fine (a) What is the characteristic equation of the closed-loop system, in terms...
Given a single cycle datapath processor with a single stuck-at-1 fault at the ALUSrc control signal (i.e. regardless of what it should be, the signal is always one) which of the following instructions will FAIL? (mark ALL that will FAIL) a) lw b) sw c) add d) ori e) beq f) J
2. The block diagram below model a simple DC motor for speed control application. Input V(s) is the desired speed in voltage, and the output Y(s) is the actual speed. Tachogenerator, H, convert the actual speed to corresponding voltage. Amplifier Motor and gears X() 5 Ls +R Tachogenerator H The following parameters are known about the system: Amplifier gain: A=2; Motor inductance: L=5H Tachogenerator gain: H=0.15; Determine the following: The system transfer function The value of the motor resistance, R,...
please answer all
A car is going with a constant tangential acceleration (i.e. increasing speed) in a circular path. As seen from above, the path is counter-clockwise. It crosses the point 'A' at time 0.00, at which point its speed is known. Find the direction of its centripetal acceleration at some time after it crosses the point A:Write your answer in degrees. Given: Speed when it crosses point 'A' - V-3.6 m/s, tangential acceleration a 3.6 m/s2, radius of path...
2. We wish to control the speed of the tumbler in a clothes dryer. To do this we must first find the transfer of the open loop system. A permanent magnet DC motor (armature controlled) is used to drive the tumbler. A power amplifier is used to drive the motor. A voltage proportional to the desired speed of the tumbler is applied at the amplifier input. a. Identify the inputs and outputs of this system. b. Identify the components. c....
Problems 3-5 (1pt each) a toy factory and need a 3-sigma X control chart to monitor the amount of red dye irn dye follows a normal distribution. When the -6.3. They their red paint used on their fire trucks. The amount of red process is in control, the mean and standard deviation amount of red dye are μ have the following data: 36 and σ Sample Mean Sample Dye Measurements 32, 38, 35 34, 39, 31 Time Period 25,24,19 3....