ZuoTi.Pro
Question

Determine the friction loss, F, for the cases below: a) Water flows through a 30 m, 4-in Schedule 40 pipe at 100 L/min. Table
engineering   Chemical-Engineering   
0 0
Add a comment Improve this question Transcribed image text
Next > < Previous
Sort answers by oldest

Homework Answers

Answer #1

solution a) Given Conditions - Length: 3om Diameter = 4 inch Boot Oz 100 L 0.00167 min Inside Diameter z 4.026 inch z m3 0.10wood Equation pz 0,094 10.225 + 0.53 + 88 E Le jour (Rejt Re 4000 5x107 0.ooool - Oioy E = roughness factor Here, we have con0,15 g friction 2.out AXV II d ²x v x (0.12 ? x 1 3.14x coll x1 03 O z rabe u sud Re = 1000 61X0.1 0.00089 м Rez 112359 55 Hfa 0.045+0.0212 + 21-2 200974,2 [fa 0.0663 fanning friction factor hs 2 4 Flv? 28D assumed here, hs a 4x 0.0663 X 1x12 Length

0 0
Add a comment
Know the answer?
Add Answer to:
Determine the friction loss, F, for the cases below: a) Water flows through a 30 m,...
Your Answer:

Post as a guest

Your Name:

What's your source?

Earn Coins

Coins can be redeemed for fabulous gifts.

Log In

Sign Up

Not the answer you're looking for? Ask your own homework help question. Our experts will answer your question WITHIN MINUTES for Free.
Similar Homework Help Questions

  • 1. (20 points) Supplementary: Hot water at 98 °C flows through a 2-in schedule 40 horizontl steel...

    Heat Exchanger type Problem, need help thanks! 1. (20 points) Supplementary: Hot water at 98 °C flows through a 2-in schedule 40 horizontl steel pipe (k 54 WIm C) and is exposed to atmospheric air at 20 °C. The water velocity is 25 cm/s. Calculate the overall heat transfer coefficient based on the outer area of the pipe whose dimensions are ID = 2.067 in.-0.0525 m and OD = 2.375 in.-0.06033 m 1. (20 points) Supplementary: Hot water at 98...

  • Determine the heat loss of seawater flowing through a 1 inch schedule 40 PVC pipe. The...

    Determine the heat loss of seawater flowing through a 1 inch schedule 40 PVC pipe. The inner diameter of the pipe is 1 inch and the outer diameter is 1.049 inches. The temperature of the water is 50 degrees F and the outside air is 72 degrees F. The seawater is flowing at 3 GPM. The thermal conductivity of the PVC pipe is 0.20 [W/(mK)].  The heat transfer coefficient between the water and the pipe is 75 [W/m2K]. Take the same...

  • Question 4: Water at 20C flows through a inch schedule 40 steel pipe at a mean...

    Question 4: Water at 20C flows through a inch schedule 40 steel pipe at a mean velocity of 0.25m/s. If the flow is fully developed and the pipe considered isothermal, find a) The heat transfer coefficient b) The friction factor.

  • 3. Water (70°F) flows through a nominal 4-in, schedule 40, PVC pipe at the rate of...

    3. Water (70°F) flows through a nominal 4-in, schedule 40, PVC pipe at the rate of 6 cfs. a. Use the Swamee-Jain equation to find the resistance coefficient b. Use the Moody Diagram to find the resistance coefficientſ.

  • Water flows according to the diagram shown below, its the globe valve in the system is...

    Water flows according to the diagram shown below, its the globe valve in the system is fully open, determine flow for: a) The total length of the pipe is 50-m, with an internal diameter of 15.8-mm, the loss coefficients are: 0.5 for inlet, 1.5 for each elbow, 10 for the valve. Using commercial steel pipe with a roughness of 0.045-mm. b) The same data, but with commercial PVC pipe 3 m 15 m Valve

  • 1) Water at "standard" conditions flows from the tank through a 6" schedule 40 pipe of...

    1) Water at "standard" conditions flows from the tank through a 6" schedule 40 pipe of length Land drains into an open reservoir at a rate of 500 gal min1. The water in the tank is h 10 m above the open end of the pipe. With all other conditions the same, we replace the 6" pipe with an 8" pipe. What is the new flowrate, Q lgal min']? (assume entrance losses and kinetic energy are negligible.) - -0 Gven...

  • 11. The head loss due to friction is found to be 12 m when water flows...

    11. The head loss due to friction is found to be 12 m when water flows 2.5 m/s in a 60-cm- diameter horizontal pipe. The pipe has a friction factor of 0.013. What is the length of the pipe over which these losses are measured? a) L= 120 m b) L=620 m c) L = 1200 m d) L = 1700 m

  • Water at 27℃ flows from a storage tank through 170 m of a steel pipe

    Water at 27℃ flows from a storage tank through 170 m of a steel pipe with an internal diameter of 154 mm. Taking the energy loss due to friction into account, calculate the required head h above the pipe inlet to produce a volume flow rate of 70.8 L/s.

  • Water flows through a 30-cm-diameter pipe that is 60 m long and made from commercial steel...

    Water flows through a 30-cm-diameter pipe that is 60 m long and made from commercial steel ssure is 240 kPa. The pi downward such that the downstream point has an elevation of 2 m and the pressure is 135 kPa a) Using an iterative scheme, what is the flowrate through the pipe? Show at least an initial guess and one iteration by hand calculations, See the in-class Type Ill problem for an example of what these hand calculations should look...

  • (b) Water flows under gravity through a pipeline connecting two reservoirs as shown in Figure 2....

    (b) Water flows under gravity through a pipeline connecting two reservoirs as shown in Figure 2. The pipeline consists of 2 km of pipe diameter 400 mm and sand roughness equivalent 0.03 mm followed by an abrupt change to 3 km of 500 mm diameter pipe of sand roughness equivalent 0.08 mm. The pipe discharges as a free jet into a reservoir. The difference in elevation between the water surface of the upstream reservoir and the discharging jet is 21...

ADVERTISEMENT
Free Homework Help App
Download From Google Play
Scan Your Homework
to Get Instant Free Answers
Need Online Homework Help?
Ask a Question
Get Answers For Free
Most questions answered within 3 hours.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT