An axle of radius 12 0 cm is used with a wheel of radius 62.0 cm....

Question

Question

An axle of radius 12 0 cm is used with a wheel of radius 62.0 cm. what force must be applied to the rim of the wheel to lift a weight 975 N

Answer 1

Answer #1

Fe 975 X 1200m 188 구 1 N

Answer 2

Similar Homework Help Questions

A wheel with mass of 5 kg and a radius of 15 cm is mounted so...

A wheel with mass of 5 kg and a radius of 15 cm is mounted so that it spins on an axle through its center. A light-weight string is wound around the circumference of the wheel. If a constant force of 3.0 N is applied to the end of the string for 1.0 seconds, what will be the change in the angular velocity? (Model the wheel as though it were a uniform cylinder.)
A string is wrapped around a wheel of radius 25 cm mounted on a stationary axle....

A string is wrapped around a wheel of radius 25 cm mounted on a stationary axle. The wheel is initially not rotating. You pull the string with a constant force through a distance of 36 cm. What is the angle in radians and degrees through which the wheel rotates? = ??? rad = ???
A bicycle wheel has a diameter of 64.0 cm and a mass of 1.76 kg. Assume...

A bicycle wheel has a diameter of 64.0 cm and a mass of 1.76 kg. Assume that the wheel is a hoop with all of the mass concentrated on the outside radius. The bicycle is placed on a stationary stand and a resistive force of 119 N is applied tangent to the rim of the tire. (a) What force must be applied by a chain passing over a 8.99 cm diameter sprocket if the wheel is to attain an acceleration...

A device is made of a wheel with an inner drum and is mounted on a...

A device is made of a wheel with an inner drum and is mounted on a frictionless axle so it does not translate but can rotate about its centre. As indicated in the figure, this device is used to lift a 30.0 kg box. The outer radius R of the device is 0.500 m and the radius of the inner drum is 0.200 m. A constant horizontal force F of magnitude 140 N is applied horizontally, as shown, to a...
Up A #4. [Gyroscope Wheel] A rubber wheel on a steel rim spins freely on a...

Up A #4. [Gyroscope Wheel] A rubber wheel on a steel rim spins freely on a horizontal axle that is suspended by a fixed pivot at point P. When the wheel spins at a rate of 4.00 rev / s, it precesses smoothly about point Pin a horizontal plane with a period of 3.50 s. The wheel's outer radius is 15.0 cm, and it's total mass is measured to be 1.12 kg, 60% of this being the spinning wheel and...
A wheel with radius 0.4m is mounted on an axle and is free to rotate. Beginning...

A wheel with radius 0.4m is mounted on an axle and is free to rotate. Beginning with the wheel at rest, a string wrapped around the edge of the wheel, is pulled with a force of 20 N . While the string is unwinding the wheel rotates through an angle of 10 rad . If the angular speed of the wheel after the string is pulled is 4 rad/s , what is the moment of inertia of the wheel?

The wheel in the figure to the right has eight equally spaced spokes and a radius...

The wheel in the figure to the right has eight equally spaced spokes and a radius of 30 cm. It is mounted on a fixed axle and is spinning at 25 rev/s You want to shoot a 20-cm-long arrow paraliled to this asle and through the wheel without hit- ting any of the spokes. Assume that the arrow and spokes are very thin (a) What minimum speed must the arrow have? Does it matter where between the axle and the...
Problem: A wheel consists of a disk of outer radius R = 1.6 m, with a...

Problem: A wheel consists of a disk of outer radius R = 1.6 m, with a concentric axle of inner radius r = 0.48 m. The wheel is pulled by a rope looped around the axle. The total mass of the wheel (disk + axle) is M = 12.0 kg and its moment of inertia is I = 18.4 kg m/s. A constant force F = 110 N applied horizontally at the circumference of the axle, causes the wheel to...
Static Equilibrium Lab: Wheel and Axle If you wanted to lift something heavy using this device, w...

Static Equilibrium Lab: Wheel and Axle If you wanted to lift something heavy using this device, would you have the heavy object connected to the larger disc and then pull one the smaller disc, or vice-versa? Why? What would be the effect of using this device on the speed that the object lifts? That is, if you pulled your string at a speed of 10 cm/s, would the object lift 10 cm/s, or would it lift faster or slower? Activity...

In the figure, what magnitude of force applied horizontally at the axle of the wheel is...

In the figure, what magnitude of force applied horizontally at the axle of the wheel is necessary to raise the wheel over an obstacle of height h = 0.303 m? The wheel's radius is r = 0.695 m and its mass is m = 1.71 kg.