Homework Answers
Add Answer to:
Compute the sensitivity for a receiver using an amplifier with noise factor 1.3 (linear) that requires...
Problem 3 A receiver has a bandwidth of 1 MHz and a noise figure of 10...
Problem 3 A receiver has a bandwidth of 1 MHz and a noise figure of 10 dB. The receiver sensitivity is -90 dBm. The Boltzmann constant is k=1.38x10-23 Joule/deg K, and the room temperature is 300 deg Kelvin. a) What is the ratio of the SNR at the input to the receiver (computed over the bandwidth of interest) to the SNR at the output of the receiver? b) What is the noise power at output of the receiver? c) Find...
3) A wireless receiver needs to meet the sensitivity requirement of -90 dBm. The channel bandwidth...
3) A wireless receiver needs to meet the sensitivity requirement of -90 dBm. The channel bandwidth is 1 MHz. The data rate is 0.5 Mbps. The antenna temperature is 290 K. (Please show all steps to receive full credits) a) If Eb/No requirement is 10 dB. What is the SNR requirement in dB? (10 pts) b) [independent of (a)] If SNR requirement is 10 dB, what is the NF requirement in dB? (15 pts)
Consider a typical optical receiver that contains a InGaAs pin photodiode, a load resistor, and an...
Consider a typical optical receiver that contains a InGaAs pin photodiode, a load resistor, and an amplifier. The receiver has the following parameters at the wavelength 1.15e-5 m: The dark current is 5.0 nA, the quantum efficiency is 0.85, and the surface leakage current is negligible. The incident optical power is 3 mW, load resistance is 50 ohm, and the effective noise bandwidth of the receiver is 1 GHz. (1) Determine the photocurrent Iph . (2) Calculate...
Photodiode Detectors
Consider the transimpedance amplifier optical receiver shown in Fig. 14-19. Thefeedback resistance is 10 k_ and the feedback capacitance is 0.2 pF. The diode’s capacitance is 5 pF, and its responsivity is 0.5 A/W. The incident optical power is 0.5 mW. (a) Compute the signal current. (b) Compute the receiver’s output voltage. (c) Compute the receiver’s 3 dB electrical bandwidth. (d) Compute the rms thermal-noise current generated in the feedback resistor, assuming a temperature of 300K. (e) Assuming no dark...
71. A superheterodyne receiver tunes at the frequency range from 25 to 50 MHz. What is the IF frequency of the rece...
71. A superheterodyne receiver tunes at the frequency range from 25 to 50 MHz. What is the IF frequency of the receiver if the range of the local oscillator is 10 MHz to 35MHz 75. An AM transmitter uses high-level modulation. The RF power amplifier draws 12 A from 22 V supply putting out a carrier power of 140 Watts. What impedance would be seen at the modulation transformer secondary? 72. A receiver has a sensitivity of 0Suv and blocking...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandw...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandwidth 5 kHz, the receiver output SNR is required to be at least 47 dB. The receiver is as shown in Fig. 8.30. (a) What must be the signal power Si received at the receiver input? (b) What is the receiver output noise power No? (c) What is the minimum transmitted power Sr if the channel transfer function is He)10-3 over...
3. The quality of a received signal is often characterized by the signal-to-noise-ratio (SNR), which is...
3. The quality of a received signal is often characterized by the signal-to-noise-ratio (SNR), which is defined as SNR 10 log As you might expect from this Signal power in watts KTB definition, the unit of SNR is decibels (dB). The term in the denominator is the noise power, and it is generally specified as an effective noise temperature T multiplied by the product of Boltzmann's constant (K) and the bandwidth (B) of the signal in Hz. Generally we like...
12 oblem # 6 The front-endof has a a radio receiver has a preamplifier followed by a mixer stage. The mixer stage with lactorN2-100 and the pre amplifier has NF, 9 dB. The overall noise factor of...
12 oblem # 6 The front-endof has a a radio receiver has a preamplifier followed by a mixer stage. The mixer stage with lactorN2-100 and the pre amplifier has NF, 9 dB. The overall noise factor of the 11.04. Suppose a signal of power-level equal to 5 dBm is watts,h imput of the preamplifier. Determine the output power-level of the preamplifier in Useful hint-Friis formula: SOLUTION
12 oblem # 6 The front-endof has a a radio receiver has a preamplifier...
3. (a) What is noise, noise voltage and noise power due to a resistor and why understanding and c...
3. (a) What is noise, noise voltage and noise power due to a resistor and why understanding and controlling of noise is critical in telecom signal transmission? Estimate the noise voltage and noise power generated by a 1 MO resistor at RT 40 °C if BW is 18 MHz. Is this noise significant? [Hint: en V 4kT (Bw)R, Pn kT (BW), k 1.38x102 [10] (b) Define channel capacity C and explain how it is affected by the S/N ratio. The...
Question 1 The noise floor, also known as additive white Gaussian noise (AWGN), is a continuous...
Question 1 The noise floor, also known as additive white Gaussian noise (AWGN), is a continuous noise level that appears over a wide spectrum when viewed in the frequency domain. True False 10 points Question 2 When considering the impact of impulse noise, we find that it is more devastating to a digital communications link, than an analog one. Therefore, error control methods should be used on all digital links. True False 10 points Question 3 When two transmitters operate...
Problem 3 A receiver has a bandwidth of 1 MHz and a noise figure of 10 dB. The receiver sensitivity is -90 dBm. The Boltzmann constant is k=1.38x10-23 Joule/deg K, and the room temperature is 300 deg Kelvin. a) What is the ratio of the SNR at the input to the receiver (computed over the bandwidth of interest) to the SNR at the output of the receiver? b) What is the noise power at output of the receiver? c) Find...
3) A wireless receiver needs to meet the sensitivity requirement of -90 dBm. The channel bandwidth is 1 MHz. The data rate is 0.5 Mbps. The antenna temperature is 290 K. (Please show all steps to receive full credits) a) If Eb/No requirement is 10 dB. What is the SNR requirement in dB? (10 pts) b) [independent of (a)] If SNR requirement is 10 dB, what is the NF requirement in dB? (15 pts)
71. A superheterodyne receiver tunes at the frequency range from 25 to 50 MHz. What is the IF frequency of the receiver if the range of the local oscillator is 10 MHz to 35MHz 75. An AM transmitter uses high-level modulation. The RF power amplifier draws 12 A from 22 V supply putting out a carrier power of 140 Watts. What impedance would be seen at the modulation transformer secondary? 72. A receiver has a sensitivity of 0Suv and blocking...
8 8.6-4 For a DSB-SC system with a channel noise PSD of Sn() 10-12 and a baseband signal of bandwidth 5 kHz, the receiver output SNR is required to be at least 47 dB. The receiver is as shown in Fig. 8.30. (a) What must be the signal power Si received at the receiver input? (b) What is the receiver output noise power No? (c) What is the minimum transmitted power Sr if the channel transfer function is He)10-3 over...
3. The quality of a received signal is often characterized by the signal-to-noise-ratio (SNR), which is defined as SNR 10 log As you might expect from this Signal power in watts KTB definition, the unit of SNR is decibels (dB). The term in the denominator is the noise power, and it is generally specified as an effective noise temperature T multiplied by the product of Boltzmann's constant (K) and the bandwidth (B) of the signal in Hz. Generally we like...
12 oblem # 6 The front-endof has a a radio receiver has a preamplifier followed by a mixer stage. The mixer stage with lactorN2-100 and the pre amplifier has NF, 9 dB. The overall noise factor of the 11.04. Suppose a signal of power-level equal to 5 dBm is watts,h imput of the preamplifier. Determine the output power-level of the preamplifier in Useful hint-Friis formula: SOLUTION
12 oblem # 6 The front-endof has a a radio receiver has a preamplifier...
3. (a) What is noise, noise voltage and noise power due to a resistor and why understanding and controlling of noise is critical in telecom signal transmission? Estimate the noise voltage and noise power generated by a 1 MO resistor at RT 40 °C if BW is 18 MHz. Is this noise significant? [Hint: en V 4kT (Bw)R, Pn kT (BW), k 1.38x102 [10] (b) Define channel capacity C and explain how it is affected by the S/N ratio. The...
Most questions answered within 3 hours.
-
What will the standard deviation of these exam grades be? A
square bracket means inclusive, so...
asked 3 minutes ago -
Beginning Retained Earnings are $ 79 comma 000 $79,000; sales
are $ 31 comma 700 $31,700;...
asked 5 minutes ago -
Please explain/demonstrate how to use NLTK to test unigram,
bigram, and trigram character models on guessing...
asked 12 minutes ago -
what you feel is most important to you and why regarding your
typing skills?
asked 13 minutes ago -
Consider a play of the casino game `Quick Draw'. In this game, a
player pays $11...
asked 22 minutes ago -
How do the mechanical features of bone affect its roles as
repositories of phosphate and calcium,...
asked 26 minutes ago -
P agreed to buy 100 barrels of widget oil, which was stored in a
large tank...
asked 26 minutes ago -
The unstable isotope 40K is used for dating rock samples. Its
half-life is 1.28×109y. How many...
asked 29 minutes ago -
Compare and contrast constructed-response items and
selected-response items.
Identify at least one (1) advantage and one...
asked 31 minutes ago -
A) Find the moment of inertia of a 2 meter long stick with a
mass of...
asked 30 minutes ago -
For the code below write a public static main() method
in class Student that:
- creates...
asked 32 minutes ago -
Please show all steps. Thank you
A 1.0-cm-diameter pipe widens to 2.0 cm, then narrows to...
asked 45 minutes ago