5. Due to an applied loading, an element at a point on a machine shaft is...
O Due to an applied loading, an element at the point on a machine shaft is subjected to the state of plane stress shown in the figure. O Determine the principal stresses and the absolute maximum shear stress at the point Ox = –20 psi, Oy = Opsi, Txy = -40 psi . 20 psi 40 psi
75 MPa 125 MPa 50 MPa At a point in a machine component subjected to plane stress there are normal and shear stresses on horizontal and vertical planes through the point, as shown. Determine the principal stresses, the maximum in-plane shear stress and associated average normal stress at the point. Also, for each case, determine the corresponding orientation of the element with respect to the element shown.
1. Given a plane element in a body is subjected to a normal tensile stress in the x-direction of 120 MPa, a normal stress in the y-direction of-75 MPa and shear stresses of 50 MPa, as shown. Determing a. What is the maximum principal stress? b. What is the minimum principal stress? 75 MPa What is the maximum shear stress? 50 MPa c. d. what is the angle to the principal plane, θ e. What is the angle to the...
3. The state of plane stress at a point is shown on the element below. Construct Mohr's circle. Determine the principal stresses acting at this point and their orientation D,. Also determine the maximum in-plane shear stresses and the orientation of the element upon which they act. What is the state of stress if it is rotated 20° counterclockwise? (20 points) 90 MPa 60 MPa -20 MPa
The state of plane stress at a point under the surface of the ANKA airplane wing is represented on the element oriented as shown in the Figure. Deternine principal Stresses Calculate the maximum in-plane shear stress and associated average normal stress by using the analytical method and Mohr's circle. For each case, determine the corresponding orientation of the element with respect to the element shown and sketch the state of stress on the element. Determine the absolute maximum shear stress...
a) The state of stress at a point is shown on the element in Figure Q4(a) Deternine i) The principal stresses (in-plane) and the corresponding principal planes; 1) The maximum in-plane shear stress and the orientation of the corresponding plane as well as the normal stress on that plane. 60 MPa 30 MPa 45 MPa Figure Q4(a)
Problem 6 (15 points) The state of plane stress at a point is shown on the element in Figure 6. a. Using Mohr's circle, determine the principal stresses and the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case. b. Represent the state of stress on an element oriented 30° counterclockwise from the position shown in Figure 6. 20 MPa 100 MPa 40 MPa Figure 6 (plot Mohr's circle on the next...
The state of stress in an elastically deformed element is given
in the table below. Determine the principal values of the stresses
and their principal direction. Also determine the maximum in plane
shear stresses and the absolute shear stress.
Stresses in MPa Cy 100 zX xy 30 -50 12 0 -40
Stresses in MPa Cy 100 zX xy 30 -50 12 0 -40
(50 Marks) a) As part of the product development process for go-kart drive shaft, the engineer has instrumented a critical area of the shaft with a solid bar. A drive shaft bar is designed to carry a tensile load. The engineer has proposed a circular bar with cross-section having a radius of 2X mm. It carries an axial tensile load of İY0 kN. By using equation; i) Calculate the values of principal stresses at the critical area of the bar....
The strain rosette shown was
used to obtain normal strain data at a point on the free surface of
a machine component. Given the values εa= -185 με, εb= -150 με, εc=
55 με, E = 10,800 ksi, and v = 0.33,
determine
(a) the stress components σx, σy, and τxy at the point.
(b) the principal stresses and the maximum in-plane shear stress at
the point; on paper, show these stresses on an appropriate sketch
that indicates the orientation...