I do not need to actually make one, just the logistics of the circuit.
I do not need to actually make one, just the logistics of the circuit. Use the...
I NEED CLEAN HANDWRITING PLEASE OR JUST LEAVE IT TO WHO CAN DO IT. !!! I. Design a circuit using a 2N3904 BIT which provides a collector current of 5±0.1 mA, and is driven by a single voltage supply having value s 15 V. Verify operation for the entire range of possible Bdc values as per the transistor specification sheet (attach relevant page). Verify your design with an LTspice simulation (just one simulation). Determine the largest possible value of Rc...
In this tutorial you will analyse a solar powered Christmas tree. The tree has a solar panel at the top, a battery at the base, and bulb string lights around it. The bulb string lights are made from 4 parallel strings with 8 light bulbs in series each. Each light bulb has a nominal resistance of 8 2. The resistance of the wiring is negligible. The battery is charged during the day to keep the bulb string lights shining at...
3. A 25-kW, 230-V shunt motor has an armature resistance of 0.064 Ω and a field-circuit resistance of 95 Ω. The motor delivers rated output power at rated voltage when its armature current is 122 A. When the motor is operating at rated voltage, the speed is observed to be 1150 r/min when the machine is loaded such that the armature current is 69.5 A a. Calculate the rated-load speed of this motor In order to protect both the motor...
I JUST NEED THE CORRECT ANSWER NO NEED FOR JUSTIFICATION Question 1 Not yet answered Marked out of 8.00 Flag question Thevenin resistance of a circuit containing only independent sources is found by then calculating the resistance seen from the terminals of the circuit Select one: a. Opening all current sources b. Shorting all voltage sources c. Opening all voltage sources and shorting all current sources d. Shorting all voltage sources and opening all current sources Question 2 Not yet...
Question 4. (a) A full-wave bridge rectifier power supply is powered from the secondary of a transformer which has a rms secondary voltage of 15.6V. The primary of the transformer is connected to a 50Hz, 230VRMS power supply. A 2700uF filter capacitor is used. A current of 1.5 Amp is drawn from the supply. (i) Sketch a schematic diagram of the setup. (ii) Calculate the mean de output voltage. Assume each power diode has a forward voltage drop of 1...
I just need help with parts d and e and what equation i would use to make my graph 7. The input voltage for the circuit shown in Figure 6.22 is given by Vc(t)- Vo cos ot. Figure 6.22. Circuit for Problem 7 (a) Find the equivalent impedance of all three components in the complex notation. (b) What is the expression for amplitude of the current? (c) What is the expression for the phase difference between the current and the...
I just need f, g, and h. Consider the circuit below, where R-5000Ω ,C-0.25μF . The voltage amplitude is 10 V and the frequency of oscillation is ω-180 rad / s , when voltages and currents are requested, express them in purely real terms. Note: this circuit is examined in some detail in Chapter 7, section 2. Have a look at that first. What is the total impedance? Express it as both a complex number and as magnitude and phase....
I just need c, d, and e. Consider the circuit below, where R-5000Ω ,C-0.25μF . The voltage amplitude is 10 V and the frequency of oscillation is ω-180 rad / s , when voltages and currents are requested, express them in purely real terms. Note: this circuit is examined in some detail in Chapter 7, section 2. Have a look at that first. What is the total impedance? Express it as both a complex number and as magnitude and phase....
I need a full solution for those questions please, although I'm half way through question one and it is quite simple but I would like to double check if Ive got that right. like and comment are rewarded for good answers Consider the following circuit containing a switch S, an ideal battery with e.m.f. ε-20.0 V, resistors R,-: 8.00 Ω, R2-20.0 Ω and R3-30.0 Ω, and capacitors R2-20Ω RI-8Ω R3 -3082 After the switch is closed: (a) Calculate the initial...
I need help answering question 2. Very clear hand writing would be helpful. Question 1 (a) Plot a graph of the data below. I(A) V -274 -10.00 2.25 -9.00 200-8.00 150-6.00 -149-5.00 -100 -4.00 0.51 -3.00 0.74-200 -049 -100 0.00 +0.00 049 +1.00 +0.50+200 +0.99 +3.00 +0.76 +400 1.01 5.00 +1.74 6.00 175 +7.00 +2.00 +8.00 +2 49 +9.00 250 10.00 (b) Calculate the slope of the line. (c) What does the slope of the line represent? Question 2 A...