Homework Answers
Add Answer to:
3. Starting with a 2 inch-diameter rod of pure copper, we would like to process (produce)...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 6660 N. If the length of the rod is 380 mm, what must the diameter be to allow an elongation of 0.50 mm? A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of 15,700 N produces a reduction in the specimen diameter of 5 10-3 mm. Compute...
Problem 1 (10 pts) It is required to manufacture a 2.5 mm diameter copper rod from...
Problem 1 (10 pts) It is required to manufacture a 2.5 mm diameter copper rod from larger diameter stock by drawing. The rod should have a tensile strength of 300 MPa or more, a yield strength of 200 MPa or more, and ductility of 10% or more. Determine (a) the range of%CW which will allow achieving those properties, and (b) within this range clearly pick a certain%CW and determine the corresponding diameter of the starting stock. yield strength (MPa) tensile...
3. You are tasked with strengthening a 1040 steel rod via strain hardening. The component's application...
3. You are tasked with strengthening a 1040 steel rod via strain hardening. The component's application dictates a minimum of a 700 MPa yield strength while also maintaining as much ductility as possible. a. What percent cold working would you recommend? What are the associated yield strength and %EL? b. Given a starting diameter of 30mm, what should your diameter be after the prescribed cold working? 1040 Steel SEL Yield streng Mal Duct 400 Cooper 1040 Steel 2001 20 Copper...
Need ASAP, Show all steps. Thanks. Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was...
Need ASAP, Show all steps. Thanks.
Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...
02: A bar of 60 mm diameter and length of 3 meter is used to produce 500 pieces on a center lathe having the follow...
02: A bar of 60 mm diameter and length of 3 meter is used to produce 500 pieces on a center lathe having the following characteristics: . Maximum rotational speed .Minimum rotational speed .Number of speeds Lathe overall efficiency The turning process is performed at 40 m/min cutting velocity. 0.5 mm/rev longitudinal feed, 0.25 mm/rev transverse feed and 2 mm depth of cut REQUIRED 1. Calculate the TWELVE rotational speeds in rpm. 2. What rotational speed would you choose? 3....
Q-1. You are testing a circular beam of two metals, 1045 steel and 2014-T6 aluminum, in...
Q-1. You are testing a circular beam of two metals, 1045 steel and 2014-T6 aluminum, in a rotating-cantilever beam fatigue test. If you need to choose one of these metals so that you can essentially design a part made of that metal, and subject the part to a repetitive stress-amplitude without ever failing due to fatigue, which one would you choose. (See the attached figure) Q-2. What is the fatigue strength for the 1045 steel alloy, if you expect to...
1-Determine the % elongation, yield stress and ultimate tensile strength of the material tested above 2-Calculate...
1-Determine the % elongation, yield stress and ultimate tensile
strength of the material tested above
2-Calculate the elastic modulus of the material tested above
3-If a 200mm cylindrical rod of the material tested above, with
radius 20mm, was subjected to a tensile load of 200kN, what would
the length be?
4-An underground wastewater steel pipe with 2mm walls carries an
ammonia solution of 40 g/m3. The pipe is in contact with
groundwater (assume 0 g/m3 ammonia). Determine the
diffusion rate...
Question 2. (Total 18 marks) 350 350 300 300 Same plot, but with expanded x axis...
Question 2. (Total 18 marks) 350 350 300 300 Same plot, but with expanded x axis 250 250 200 Stress (MPa) Stress (MPa) 150 $150 100 100 0 0 0 0.02 0.04 0.06 0.12 0.14 0.16 0.18 0 0.08 0.1 Strain 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 0.01 Strain (a) Determine the % elongation, yield stress and ultimate tensile strength of the material tested above (3 marks) (b) Calculate the elastic modulus of the material tested above...
PROBLEM 2: Design a rectangular beam well inside the tension-controlled zone. Start calculations assuming εt=0.0075 Select...
PROBLEM 2: Design a rectangular beam well inside the
tension-controlled zone. Start calculations assuming εt=0.0075
Select b, d and As to resist a factored design moment, Mu = 255
k-ftin the tension-controlled zone.
PROBLEM 2: Design a rectangular beam well inside the tension-controlled zone. Start calculations assuming ε-0.0075 Select b, d and As to resist a factored design moment, Mu 255 k-ft in the tension-controlled zone. Material Characteristics: Compression Strength of Concrete - fc 4,000 psi Yielding stress of steel...
× HW-2. Mech Behav. Sp19.docx HWI Prob I: (Textbook problem 1.25) Two parts have been made...
× HW-2. Mech Behav. Sp19.docx HWI Prob I: (Textbook problem 1.25) Two parts have been made of the same material, but one was formed by cold working and the other by hot working. Explain the differences in mechanical behavior and surface properties you might expect to sec Prob 2: (Textbook problem 1.29) What is the significance of the fact that such metals as lead and tin have a recrystallization that is about room Prob 3: (Textbook problem 2.17) Why does...
Problem #1 A cylindrical rod of copper (E 110 GPa) having a yield strength of 240 MPa is to be subjected to a load of 6660 N. If the length of the rod is 380 mm, what must the diameter be to allow an elongation of 0.50 mm? A cylindrical specimen of some alloy 8 mm in diameter is stressed elastically in tension. A force of 15,700 N produces a reduction in the specimen diameter of 5 10-3 mm. Compute...
Problem 1 (10 pts) It is required to manufacture a 2.5 mm diameter copper rod from larger diameter stock by drawing. The rod should have a tensile strength of 300 MPa or more, a yield strength of 200 MPa or more, and ductility of 10% or more. Determine (a) the range of%CW which will allow achieving those properties, and (b) within this range clearly pick a certain%CW and determine the corresponding diameter of the starting stock. yield strength (MPa) tensile...
3. You are tasked with strengthening a 1040 steel rod via strain hardening. The component's application dictates a minimum of a 700 MPa yield strength while also maintaining as much ductility as possible. a. What percent cold working would you recommend? What are the associated yield strength and %EL? b. Given a starting diameter of 30mm, what should your diameter be after the prescribed cold working? 1040 Steel SEL Yield streng Mal Duct 400 Cooper 1040 Steel 2001 20 Copper...
Need ASAP, Show all steps. Thanks.
Supplemental Problems 10.16 A 12-in.-diameter structural nickel steel specimen was subjected to a tension test. After rupture it was determined that the 2-in. standard-gage length had stretched to 2.42 in. The minimum diameter at the fracture was measured to be 0.422 in. Compute the percent elongation and percent reduction in area. 10.20 During a tensile test of a steel specimen, the strain at a stress of 35 MPa was calculated to be 0.000 170...
02: A bar of 60 mm diameter and length of 3 meter is used to produce 500 pieces on a center lathe having the following characteristics: . Maximum rotational speed .Minimum rotational speed .Number of speeds Lathe overall efficiency The turning process is performed at 40 m/min cutting velocity. 0.5 mm/rev longitudinal feed, 0.25 mm/rev transverse feed and 2 mm depth of cut REQUIRED 1. Calculate the TWELVE rotational speeds in rpm. 2. What rotational speed would you choose? 3....
Q-1. You are testing a circular beam of two metals, 1045 steel and 2014-T6 aluminum, in a rotating-cantilever beam fatigue test. If you need to choose one of these metals so that you can essentially design a part made of that metal, and subject the part to a repetitive stress-amplitude without ever failing due to fatigue, which one would you choose. (See the attached figure) Q-2. What is the fatigue strength for the 1045 steel alloy, if you expect to...
1-Determine the % elongation, yield stress and ultimate tensile
strength of the material tested above
2-Calculate the elastic modulus of the material tested above
3-If a 200mm cylindrical rod of the material tested above, with
radius 20mm, was subjected to a tensile load of 200kN, what would
the length be?
4-An underground wastewater steel pipe with 2mm walls carries an
ammonia solution of 40 g/m3. The pipe is in contact with
groundwater (assume 0 g/m3 ammonia). Determine the
diffusion rate...
Question 2. (Total 18 marks) 350 350 300 300 Same plot, but with expanded x axis 250 250 200 Stress (MPa) Stress (MPa) 150 $150 100 100 0 0 0 0.02 0.04 0.06 0.12 0.14 0.16 0.18 0 0.08 0.1 Strain 0.001 0.002 0.003 0.004 0.005 0.006 0.007 0.008 0.009 0.01 Strain (a) Determine the % elongation, yield stress and ultimate tensile strength of the material tested above (3 marks) (b) Calculate the elastic modulus of the material tested above...
PROBLEM 2: Design a rectangular beam well inside the
tension-controlled zone. Start calculations assuming εt=0.0075
Select b, d and As to resist a factored design moment, Mu = 255
k-ftin the tension-controlled zone.
PROBLEM 2: Design a rectangular beam well inside the tension-controlled zone. Start calculations assuming ε-0.0075 Select b, d and As to resist a factored design moment, Mu 255 k-ft in the tension-controlled zone. Material Characteristics: Compression Strength of Concrete - fc 4,000 psi Yielding stress of steel...
× HW-2. Mech Behav. Sp19.docx HWI Prob I: (Textbook problem 1.25) Two parts have been made of the same material, but one was formed by cold working and the other by hot working. Explain the differences in mechanical behavior and surface properties you might expect to sec Prob 2: (Textbook problem 1.29) What is the significance of the fact that such metals as lead and tin have a recrystallization that is about room Prob 3: (Textbook problem 2.17) Why does...
Most questions answered within 3 hours.
-
10. Complete the table below
only using hexadecimal numbers:
AL CODE
EBX
EAX
[EAX]
mov eax,...
asked 2 minutes ago -
trust is best established through the combination of ------and
------- .
1. magnanimity and justice
2....
asked 17 minutes ago -
Blood pressure is normally taken on the upper arm at the level
of the heart. Suppose,...
asked 16 minutes ago -
Suppose that the satellite around the earth has an orbit that is
24 KM larger in...
asked 19 minutes ago -
Calculate the [OH (aq)] in limes which have a [H3O*(aq)] of 1.3 x
10 mol/L
asked 17 minutes ago -
A nozzle with a radius of 0.250 cm is attached to a garden hose
with a...
asked 28 minutes ago -
PLEASE do not use any loops for the program; only recursion is
allowed
4. Write a...
asked 37 minutes ago -
Please help me with me. I did the first part to write the operations but in...
asked 34 minutes ago -
Use Cryptool to find the Cryptographic SHA-1 hash value of the
string "abc". The calculator is...
asked 39 minutes ago -
You are attempting to calculate a firm’s free cash flow to
equity. You know the following...
asked 1 hour ago -
the following reaction occurs in a balloon containing
N2O2 gas
N2O4(g)=2NO2(g)
will the volume of the...
asked 2 hours ago -
answer the questions throughout this program
public class Day implements Comparable {
Private Boolean atWork;...
asked 2 hours ago