A 3-phase 50Hz 2-pole 440V (L-L rms) induction motor drive has a rated speed of 2955 rpm and rated torque of 35 Nm. This motor drives a load with a torque characteristic that increases linearly with speed such that it equals the load torque at the rated speed. It draws a current of 2.1 A(rms) per phase at the rated voltage at a power factor of 0.81 (lagging). The stator resistance Rs = 2.0 ohms. At the rated operating speed, calculate the amplitude of the phase voltage (Va,braking) needed produce a regenerative braking torque that is 0.8 times the rated torque in magnitude.
A 3-phase 50Hz 2-pole 440V (L-L rms) induction motor drive has a rated speed of 2955...
A three-phase, 50-Hz, 4-pole, 575-V (line-line, rms) induction motor drive has a full-load (rated) speed of 1450 rpm. The rated torque is 50 Nm. Keeping the air gap flux-density peak constant at its rated value, (a) plot the torque-speed characteristics (the linear portion) for the following values of the frequency: 50 Hz, 40 Hz, 30 Hz and 20 Hz. (b) This motor is supplying a load whose torque demand increases linearly with speed such that it equals the rated motor...
A 3 phase, 4 pole, 60 Hz., AC Induction Motor has a rated Torque of 150 Nm. with the phase voltage of 254v. Its parameters are: R1 = 0.20 Ohms, R2’ = 0.32 Ohms and X = 0.50 Ohms. Find its approximate slip at the rated load and speed.
1. A six pole, 240V, 50 Hz three phase squirrel-cage induction motor has a no-load speed of 103 rad/s and a speed regulation of 5% at rated load. Find the amount of slip (in rpm) at full load for this motor. 2.. A 2 HP, 240 VAC, 60 Hz, capacitor-start motor is 75% efficient and draws 10 A at full load. What is this motor's power factor at rated load? 3. A wound rotor, 3 phase induction motor in Mr....
The equivalent circuit of a 440 V, 3-phase, 8 pole, and 50 Hz star-connected induction motor is shown in figure 1. The short-circuit test is conducted with a locked rotor and a line current of 80 A. The open-circuit test is conducted by supplying the stator winding at rated voltage and at the rotor is rotating freely without any mechanical load.a) Determine the line voltage and power factor on the short circuit test;b) We need to apply a low...
A 4 phase, 460 V, 60 Hz, 26.8 hp, 4 pole, Y-connected induction motor draws 25 A at a power factor of 0.9 lagging. Core loss is 900 W, stator copper loss is 1100W, friction and winding losses are 300 W, and stray loss is neglected. The machine shaft rotates at 1738 rpm. Calculate the air gap power and output load torque - [Induction Motor - 15 points) A three-phase, 460 V, 60 Hz, 26.8 hp, 4-pole, Y-connected induction motor...
d) A 440V, 50 Hz, 4-pole, 3 phase induction motor has a total leakage impedance of (0.3 +j5.5+0.25/s) ohm (delta phase). Determine the external resistance to be inserted in each phase of the rotor winding such that the motor produce a gross torque of 130 N-m at a speed of 1300 rpm. (10 Marks) d) A 440V, 50 Hz, 4-pole, 3 phase induction motor has a total leakage impedance of (0.3 +j5.5+0.25/s) ohm (delta phase). Determine the external resistance to...
A 1.6-hp, 8-pole, 60-Hz, three-phase induction motor is rated for 820 rpm, 220 V rms (line-to-line), and 4.32 A (line current) at 77.0 percent lagging power factor. Find the full-load efficiency if the motor is delta-connected and if it is wye-connected.
A 3 phase, 440 V, 6 pole, 970 rpm, 50 Hz, Y-connected induction motor has the following parameters referred to the stator Rs = 0.2 Ω, Rr'一0.15 Ω, xs-x-= 0.4 Ω The stator to rotor turns ratio is 3.5 The motor speed is controled by the Static Scherbius Drive. The drive is designed for a speed range of 30% below the synchronous speed. The maximum value of firing angle is 170'. Calculate (i) Turns ratio of the transformer (ii) Torque...
Problem Solving: 1. A 220V, 4-pole, 60Hz, 1-phase induction motor has an effective rotor resistance and leakage reactance of 0.5 Ohms and 5 ohms respectively. It is running at a speed of 1,800 rpm. Determine: a. Frequencies of forward and backward rotor current components b. Relative magnitudes of forward and backward fluxes. Neglect magnetizing current and stator impedance. A 220-W, 2-pole, 115-V, 60-Hz single-phase induction motor delivers rated output at a slip 10%. The total copper loss at full load...
4.6. A 460-V, 75 kW, 4-pole, delta-connected, 60-Hz, three- phase induction motor has a full-load slip of 5 percent, an efficiency of 92 percent and a power-factor of 0.87 lagging at full-load. At start-up, the motor develops 1.9 times the full load developed torque but draws 7.5 times the rated current at the rated voltage. This motor is to be started with an auto- transformer reduced-voltage starter. Assume the stator resistance and the stator core loss to be negligible. Calculate...