Problem 13.42 Part A An irrigation canal has a rectangular cross section. At one point where...
Problem 13.42
Part A
An irrigation canal has a rectangular cross section. At one point where the canal is 18.4 m wide and the water is 3.90 m deep, the water flows at 2.30 cm/s . At a second point downstream, but on the same level, the canal is 16.9 m wide, but the water flows at 10.6 cm/s . How deep is the water at this point?
Express your answer in meters to three significant figures.
ANSWER:
| m |
Homework Answers
from continuity equation
A1V1 = A2V2
HERE A = L*D
18.4*3.9*0.023 = 16.9*D*0.106
D = 0.921 m
Add Answer to:
Problem 13.42
Part A
An irrigation canal has a rectangular cross section. At one
point where...
Part A - Maximum load A column is made from a rectangular bar whose cross section...
Part A - Maximum load A column is made from a rectangular bar whose cross section is 5.1 cm by 8.9 cm . If the height of the column is 2 m , what is the maximum load it can support? The material has E = 200 GPa and σY = 250 MPa . Express your answer with appropriate units to three significant figures. Pmax = ?? Part B - Maximum length A circular column with diameter 9.4 cm is...
The beam has a rectangular cross section and is subjected to the loading shown. Determine the...
The beam has a rectangular cross section and is subjected to the loading shown. Determine the state of stress at point B. Take F1 420 lb, F2 530 lb (Figure 1) Part A Find ? Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in case of tension ?,-1 Value Units Submit Request Answer Figure < 1of1 ? Part B Find ? Express your answer to three...
Leaming Goal: To determine the absolute maximum bending stress in a rectangular cross section that has...
Leaming Goal: To determine the absolute maximum bending stress in a rectangular cross section that has a circular cutout and is subjected to unsymmetrical bending in the y and z-directional planes, and to determine the angles of the neutral axes established by the applied moments. The rectangular cross section ABCD shown below has a circular cutout of diameter d= 30.0 mmthrough its center. The member is subjected to two extemally applied moments M1-6.0 kN mand M2-17.0 kN mat angles 1-35.0...
Learning Goal: To calculate the normal and shear stresses at a point on the cross section...
Learning Goal: To calculate the normal and shear stresses at a point on the cross section of a column. The state of stress at a point is a description of the normal and shear stresses at that point. The normal stresses are generally due to both internal normal force and internal bending moment. The net result can be obtained using the principle of superposition as long as the deflections remain small and the response is elastic. Figure < 1 of...
Part B Determine the resultant shear force acting on the cross section at point CC in...
Part B
Determine the resultant shear force acting on the cross section
at point CC in the beam.
Express your answer to three significant figures and include
appropriate units.
Part C
Determine the resultant bending moment acting on the cross
section at point CC in the beam.
Express your answer to three significant figures and include
appropriate units.
Show all steps and solution clearly, with correct units as asked
in problem:
Problem 7.21 The load D has a mass of...
The figure below shows a horizontal pipe with a varying cross section. A liquid with a...
The figure below shows a horizontal pipe with a varying cross section. A liquid with a density of 1.65 g/cm flows from left to right in the pipe, from larger to smaller cross section. The left side's cross-sectional area is 10.0 cm, and while in this side, the speed of the liquid is 2.50 m/s, and the pressure is 1.20 x 105 Pa. The right side's cross sectional area is 3.50 cm? (a) What is the speed (in m/s) of...
Homework Set #6-Chapter 6 Problem 6.87 4 of 10 > The beam has a rectangular cross...
Homework Set #6-Chapter 6 Problem 6.87 4 of 10 > The beam has a rectangular cross section with b = 8 in. 2b 6 ft Part A Determine the largest maximum intensity wo of the triangular distributed load that can be supported if the allowable bending stress is σ 1-1.7 ksi Express your answer to three significant figures. uo = Submit Provide Feedback Next >
Part A -Normal Strain at a Specified Point Consider the pre-deformation cross-section of a bar, a...
Part A -Normal Strain at a Specified Point Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below The dia meter of the bar is d- 120 mm. A bending moment is applied that causes the neutral axis to become conca o up. What is the normal strain h Express your answer to three significant figures. View Available Hint(s) 20 mm from the bottom of the bar if the radius of curvature...
Problem 7.56 Variable Cross Section and the Bernoulli Equation An aqueous solution with a specifi...
Help with part a on this problem. Thanks.
Problem 7.56 Variable Cross Section and the Bernoulli Equation An aqueous solution with a specific gravity of 1.12 flows through a channel with a variable cross section Data taken at two axial positions in the channel are shown here. Point 2 is 4.00 m higher than point 1. Point 1 Point 2 Pgauge 25.00 x 104 Pa 9.77 x 104 Pa u(m/s) 7.00 Velocity x Watch out for error when calculating the...
Part A Water runs from a sloping channel with a flow of 21 m/s onto a...
Part A Water runs from a sloping channel with a flow of 21 m/s onto a horizontal channel, forming a hydraulic jump. The channel is 2 m wide, and the water is y1 = 0.75 m deep before the jump. (Figure 1) Determine the depth Y2 of water after the jump. Express your answer to three significant figures and include the appropriate units. μΑ ? Figure y2 = Value 1 of 1 Units Submit Request Answer Part B Y2 What...
The beam has a rectangular cross section and is subjected to the loading shown. Determine the state of stress at point B. Take F1 420 lb, F2 530 lb (Figure 1) Part A Find ? Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive in case of tension ?,-1 Value Units Submit Request Answer Figure < 1of1 ? Part B Find ? Express your answer to three...
Leaming Goal: To determine the absolute maximum bending stress in a rectangular cross section that has a circular cutout and is subjected to unsymmetrical bending in the y and z-directional planes, and to determine the angles of the neutral axes established by the applied moments. The rectangular cross section ABCD shown below has a circular cutout of diameter d= 30.0 mmthrough its center. The member is subjected to two extemally applied moments M1-6.0 kN mand M2-17.0 kN mat angles 1-35.0...
Learning Goal: To calculate the normal and shear stresses at a point on the cross section of a column. The state of stress at a point is a description of the normal and shear stresses at that point. The normal stresses are generally due to both internal normal force and internal bending moment. The net result can be obtained using the principle of superposition as long as the deflections remain small and the response is elastic. Figure < 1 of...
Part B
Determine the resultant shear force acting on the cross section
at point CC in the beam.
Express your answer to three significant figures and include
appropriate units.
Part C
Determine the resultant bending moment acting on the cross
section at point CC in the beam.
Express your answer to three significant figures and include
appropriate units.
Show all steps and solution clearly, with correct units as asked
in problem:
Problem 7.21 The load D has a mass of...
The figure below shows a horizontal pipe with a varying cross section. A liquid with a density of 1.65 g/cm flows from left to right in the pipe, from larger to smaller cross section. The left side's cross-sectional area is 10.0 cm, and while in this side, the speed of the liquid is 2.50 m/s, and the pressure is 1.20 x 105 Pa. The right side's cross sectional area is 3.50 cm? (a) What is the speed (in m/s) of...
Homework Set #6-Chapter 6 Problem 6.87 4 of 10 > The beam has a rectangular cross section with b = 8 in. 2b 6 ft Part A Determine the largest maximum intensity wo of the triangular distributed load that can be supported if the allowable bending stress is σ 1-1.7 ksi Express your answer to three significant figures. uo = Submit Provide Feedback Next >
Part A -Normal Strain at a Specified Point Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below The dia meter of the bar is d- 120 mm. A bending moment is applied that causes the neutral axis to become conca o up. What is the normal strain h Express your answer to three significant figures. View Available Hint(s) 20 mm from the bottom of the bar if the radius of curvature...
Help with part a on this problem. Thanks.
Problem 7.56 Variable Cross Section and the Bernoulli Equation An aqueous solution with a specific gravity of 1.12 flows through a channel with a variable cross section Data taken at two axial positions in the channel are shown here. Point 2 is 4.00 m higher than point 1. Point 1 Point 2 Pgauge 25.00 x 104 Pa 9.77 x 104 Pa u(m/s) 7.00 Velocity x Watch out for error when calculating the...
Part A Water runs from a sloping channel with a flow of 21 m/s onto a horizontal channel, forming a hydraulic jump. The channel is 2 m wide, and the water is y1 = 0.75 m deep before the jump. (Figure 1) Determine the depth Y2 of water after the jump. Express your answer to three significant figures and include the appropriate units. μΑ ? Figure y2 = Value 1 of 1 Units Submit Request Answer Part B Y2 What...
Most questions answered within 3 hours.
-
Suppose that on a temperature scale X, water boils at 203.0°X
and freezes at -105.7°X. What...
asked 29 minutes ago -
BaS crystallizes in a cubic unit cell with S2- ions on each
corner and each face....
asked 1 hour ago -
A. 0≤P(Oi)≤10≤P(Oi)≤1 for each i
B. P(Oi)≤0P(Oi)≤0
C. P(Oi)=1+P(OCi)P(Oi)=1+P(OiC)
D. P(Oi)≥1P(Oi)≥1
If an experiment consists of...
asked 2 hours ago -
A battery has an emf of 9.20V and an internal resistance of 1.20
ohm. a)What resistance...
asked 2 hours ago -
The area of an elastic circular loop decreases at a constant
rate, dA/dt = −6.60×10−3 m2/s...
asked 3 hours ago -
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 5 hours ago -
Please answer what the maximum and minimum force is, and the
angle on the ion is...
asked 5 hours ago -
implement a program that reads a number of rows and a symbol.
The program will draw...
asked 5 hours ago -
Assume that when adults with smartphones are randomly selected,
45% use them in meetings or classes....
asked 5 hours ago -
Determine the number of formula units of
Na2SO4 and moles of oxygen contained in 8.11
moles...
asked 5 hours ago -
Explain in steps on the following code
What would be the output when executed
using System;...
asked 5 hours ago -
Given the information in the table, which of the following
statements is CORRECT?
Stock A
Stock...
asked 5 hours ago