Homework Answers
Hence
, the given screw is self locking for assumed value of thread
coefficient of friction.
upvote if you get it and please comment for any doubt.
Add Answer to:
15-3 A 1 3/8-4 Acme thread screw is used to lift a 1-ton load. The mean...
There are two jack screw assemblies both with an ISO Metric Trapezoidal ‘Tr 16 x 3’ screw, one single-thread and the oth...
There are two jack screw assemblies both with an ISO Metric Trapezoidal ‘Tr 16 x 3’ screw, one single-thread and the other double-thread, to raise and lower a load of 450 kg. A ball-thrust bearing forms part of the assembly and therefore collar friction is negligible. The coefficient of sliding friction for both screws is 0.08. (a) For each assembly, determine: (i) the pitch, pitch diameter, lead and lead angle; (ii) the running torque required to lower the load; (iii)...
A square power screw has a mean diameter of 30 mm and a pitch of 4...
A square power screw has a mean diameter of 30 mm and a pitch of 4 mm with single thread. The collar diameter can be assumed to be 35 mm. The screw is to be used to lift and lower a load of 7 kN. A coefficient of friction of 0.05 is to be used for friction at the thread and at the collar. Determine the following: (i) Torque required to raise the load. TR. (Equation 8.1) (ii) Torque required...
6. Consider a power screw used in an application to lift a load. In the following, select a standard power screw, a...
6. Consider a power screw used in an application to lift a load. In the following, select a standard power screw, and determine: the torque to raise and lower the load, and the efficiency of the power screw. Use a friction factor of 0.15. (15 marks) a) Select an Acme screw thread ( 14.5°) to lift a load of 15,000 Ib, limiting the tensile strength to 8,000 psi b) Select a metric trapezoidal screw thread (= 15°) to lift a...
PROBLEM 5: Figure shows a screw jack lifting a non- rotating load of 200 kg. The...
PROBLEM 5: Figure shows a screw jack lifting a non- rotating load of 200 kg. The screw jack consists of a single square screw thread with a major diameter of 30 mm and 10 threads per 5 cm. A rotating nut, driven by a leverage arm moves a plain thrust collar with diameter de 50 mm, which in turn lifts and lowers the load. The friction coefficient between the nut and the collar μ -0.25 and the friction coefficient between...
Looking for a bit of help with he below question; part C in particular. Thanks in...
Looking for a bit of help with he below question; part C in
particular. Thanks in advance!
2 There are two jack screw assemblies both with an ISO Metric Trapezoidal 'Tr 16 x 3' screw, one single-thread and the other double-thread, to raise and lower a load of 450 kg. A ball-thrust bearing forms part of the assembly and therefore collar friction is negligible The coefficient of sliding friction for both screws is 0.08 (a) For each assembly, determine: the...
1. An electrically driven screw-press is shown. The "load-bar" is raised or lowered via two threaded...
1. An electrically driven screw-press is shown. The "load-bar" is raised or lowered via two threaded screws supported via collar-bearings. Each screw is a 20mm diameter and 4mm in pitch with single square threaded. The collars each have an effective diameter of 30mm. The thread coefficients of friction is 0.075 and 0.095 for the screw and collar respectively. Each screw supports a load of 6kN. a) Find the torque required (per screw) to raise or lowerthe bar b) Determine if...
Question 1 (10 pts) A square-threaded, single thread power screw with a mean diameter of 1...
Question 1 (10 pts) A square-threaded, single thread power screw with a mean diameter of 1 in and four threads per inch is used to raise a load of 25,000 lb. The collar mean diameter is 1.5 in. The coefficient of friction is 0.1 for both the thread and the collar. Determine the following: Load 25,000 lb Q1.1. Determine the major diameter of the screw (2pts) Q1.2. Determine the screw torque required to raise the load (2pts) Q1.3. Determine the...
4. A single-start, square-threaded power screw has the following baseline character- istics: Outside diameter pitch, p...
4. A single-start, square-threaded power screw has the following baseline character- istics: Outside diameter pitch, p Load, W 25.4 mm 5.08 mm 1500 N thread friction coefficient 0.08 collar friction coefficient collar diameter 0.04 28 mm (a) What torque, TR, total, is required to raise the load? Include units. (b) What torque, TL, total, is required to lower the load? Include units (c) Suppose the screw runs at 100 rpm for ten seconds, raising the load. How much energy is...
A single-square threaded 35-mm power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reac...
A single-square threaded 35-mm power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to "raise" and "lower" the load Repeat this problem if ACME screw is used in this design.
A single-square threaded 35-mm...
A square-threaded power screw with single thread is used to raise a load of 25,000 lb....
A square-threaded power screw with single thread is used to raise a load of 25,000 lb. The screw has a mean diameter of 1-in. and four threads per inch. The collar mean diameter is 1.5 in. The coefficient of friction is estimated as 0.1 for both the thread and the collar. Assume the length of thread engagement is 1.5 times the outside diameter of the screw. 1. Calculate the safety factor for the power screw to fail in torsion. Assume...
A square power screw has a mean diameter of 30 mm and a pitch of 4 mm with single thread. The collar diameter can be assumed to be 35 mm. The screw is to be used to lift and lower a load of 7 kN. A coefficient of friction of 0.05 is to be used for friction at the thread and at the collar. Determine the following: (i) Torque required to raise the load. TR. (Equation 8.1) (ii) Torque required...
6. Consider a power screw used in an application to lift a load. In the following, select a standard power screw, and determine: the torque to raise and lower the load, and the efficiency of the power screw. Use a friction factor of 0.15. (15 marks) a) Select an Acme screw thread ( 14.5°) to lift a load of 15,000 Ib, limiting the tensile strength to 8,000 psi b) Select a metric trapezoidal screw thread (= 15°) to lift a...
PROBLEM 5: Figure shows a screw jack lifting a non- rotating load of 200 kg. The screw jack consists of a single square screw thread with a major diameter of 30 mm and 10 threads per 5 cm. A rotating nut, driven by a leverage arm moves a plain thrust collar with diameter de 50 mm, which in turn lifts and lowers the load. The friction coefficient between the nut and the collar μ -0.25 and the friction coefficient between...
Looking for a bit of help with he below question; part C in
particular. Thanks in advance!
2 There are two jack screw assemblies both with an ISO Metric Trapezoidal 'Tr 16 x 3' screw, one single-thread and the other double-thread, to raise and lower a load of 450 kg. A ball-thrust bearing forms part of the assembly and therefore collar friction is negligible The coefficient of sliding friction for both screws is 0.08 (a) For each assembly, determine: the...
1. An electrically driven screw-press is shown. The "load-bar" is raised or lowered via two threaded screws supported via collar-bearings. Each screw is a 20mm diameter and 4mm in pitch with single square threaded. The collars each have an effective diameter of 30mm. The thread coefficients of friction is 0.075 and 0.095 for the screw and collar respectively. Each screw supports a load of 6kN. a) Find the torque required (per screw) to raise or lowerthe bar b) Determine if...
Question 1 (10 pts) A square-threaded, single thread power screw with a mean diameter of 1 in and four threads per inch is used to raise a load of 25,000 lb. The collar mean diameter is 1.5 in. The coefficient of friction is 0.1 for both the thread and the collar. Determine the following: Load 25,000 lb Q1.1. Determine the major diameter of the screw (2pts) Q1.2. Determine the screw torque required to raise the load (2pts) Q1.3. Determine the...
4. A single-start, square-threaded power screw has the following baseline character- istics: Outside diameter pitch, p Load, W 25.4 mm 5.08 mm 1500 N thread friction coefficient 0.08 collar friction coefficient collar diameter 0.04 28 mm (a) What torque, TR, total, is required to raise the load? Include units. (b) What torque, TL, total, is required to lower the load? Include units (c) Suppose the screw runs at 100 rpm for ten seconds, raising the load. How much energy is...
A single-square threaded 35-mm power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45 mm. Find the overall efficiency and the torque to "raise" and "lower" the load Repeat this problem if ACME screw is used in this design.
A single-square threaded 35-mm...
Most questions answered within 3 hours.
-
find the critical value associated with a right sided hypothesis of
the mean using a sample...
asked 1 hour ago -
Which of the following statements is true with respect to a
simple linear regression model?
a....
asked 1 hour ago -
The energy required to remove an electron from a surface of a
solid element is called...
asked 3 hours ago -
How would you train your employees to avoid risks of using
mobile devices?
asked 3 hours ago -
Assume Kw = 1.01 ✕ 10−14
For pure water, we can calculate [H3O+ ] = [OH...
asked 4 hours ago -
Suppose that on a temperature scale X, water boils at 203.0°X
and freezes at -105.7°X. What...
asked 5 hours ago -
BaS crystallizes in a cubic unit cell with S2- ions on each
corner and each face....
asked 5 hours ago -
A. 0≤P(Oi)≤10≤P(Oi)≤1 for each i
B. P(Oi)≤0P(Oi)≤0
C. P(Oi)=1+P(OCi)P(Oi)=1+P(OiC)
D. P(Oi)≥1P(Oi)≥1
If an experiment consists of...
asked 7 hours ago -
A battery has an emf of 9.20V and an internal resistance of 1.20
ohm. a)What resistance...
asked 7 hours ago -
The area of an elastic circular loop decreases at a constant
rate, dA/dt = −6.60×10−3 m2/s...
asked 8 hours ago -
The denaturation of proteins can be described by the
equilibrium
F⇌U
where F and U represent...
asked 10 hours ago -
Please answer what the maximum and minimum force is, and the
angle on the ion is...
asked 10 hours ago