1. If you have a 1.875" diameter shaft, what size key would you specify (H x...
Determine a standard size for a key to fit in a 0.83" diameter shaft transmitting 2819 in-lbs of torque with n 1.1
It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...
QUESTION 1 The cross section of a key for a 41 mm diameter shaft. The Torque transmitted by shaft to hub is 636,348 N-mm. The key is made of steel having Syt - 380 MPa and the factor of safety is 2. Determine the length of the key (mm) in Shear.
The solid steel shaft (Sy = 75 kpsi, Se = 50 kpsi, Sut = 110 kpsi) carrying two-belt pulleys is shown in the figure (reaction force, torques are given as well). Two pulleys are keyed to the shaft where pulley B is of diameter 4.0 in the pulley C is of diameter 8.0 in. Assume the shaft has a uniform diameter d = 1.5 in. 1) Design a key (S, = 60 kpsi) for pulley C using the design factor...
for the shaft shown below answer thefollowing:1. Find the factor of safety in point H ifthe shaft is made from carbon steels1030 hot rolled and the shaftdiameter is 32 mm.2. Find the diameter of the shaft if itmade from wrought-aluminum alloy2024 heat treated and the factor ofsafety is 2.3. Select suitable carbon steel alloy forthat shaft if its diameter is 25 mmand factor of safety required is 1.5.
-a) Motor shaft 030 will be fitted to a flange with H7 tolerance on the hole. If the motor shaft is to be fitted as Clearance Fit to provide 0.002mm min.clearance and the 0.032mm max.clearance in the flange, what are the most suitable tolerances for the motor shaft? Specify the size of the shaft you would include on the drawing. Please comply with the ISO FITS HOLE BASIS , Data Sheet 4500A? (12 pts) Notes: show all your calculations and...
help pls
1) A copper collar is to fit tightly about a steel shaft whose diameter is 6.0057 cm at 18 C. The inside diameter of the copper collar at that temperature is 5.9800 cm. To what temperature must the copper collar be raised so that it will just sip on the steel shaft, assuming the temperature of both the steel shaft and copper collar are raised simultaneously? "С | Submit You currentily have submisslons for this question. Only 5...
Describe how you would make a precision shaft with dimensions of 12 mm diameter, 30 mm long from cemented carbide.
6. For the bearing with the largest radial load and without
knowing the shaft diameter, what would be the catalog rating for a
radially loaded ball bearing to withstand 1000 x 10e6 cycles with
90% reliability. The bearing manufacturer rates its bearing for a
million cycles.
7. A 10 mm diameter steel shaft is subject to bending stresses
only. The material has Sut = 1100 MPa and Sy = 950 MPa and a
fine-ground surface finish.
1. Determine the factor...