Determine a standard size for a key to fit in a 0.83" diameter shaft transmitting 2819...

Question

Question

Answer 1

Answer #1

Let u consiclenMg to the cold -dva Sleel for 5 ie Sut =61 ksi Since (Ss)oSx 61 ss . ь, f n Volub ape Substitute L= 6792.77 L

Answer 2

Similar Homework Help Questions

It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power a...

It is required to design a square key for fixing gear on a shaft of 50 mm diameter. 14 KW power at 317 rps is transmitted from the shaft to the gear. Determine the applied Torque in N-m It is required to design a key for fixing gear on a shaft of 50 mm diameter. It is required that 15 kW power at 720 rpm is to be transmitted from the shaft to the gear. The yield strength of the...
QUESTION 1 The cross section of a key for a 41 mm diameter shaft. The Torque...

QUESTION 1 The cross section of a key for a 41 mm diameter shaft. The Torque transmitted by shaft to hub is 636,348 N-mm. The key is made of steel having Syt - 380 MPa and the factor of safety is 2. Determine the length of the key (mm) in Shear.
The following dimensions are given for a standard press and shrink fit of a solid shaft...

The following dimensions are given for a standard press and shrink fit of a solid shaft and a collar: basic size: 40 mm maximum hole diameter: 40.025 mm minimum hole diameter: 40.000 mm maximum shaft diameter: 40.060 mm minimum shaft diameter: 40.044 mm The materials are both carbon steel. Find the maximum and minimum values of: i) the radial interference ii) the interference pressure Use a collar outside diameter of 80 mm.

QUESTION 1 It is required to design a square key for fixing a gear on a...

QUESTION 1 It is required to design a square key for fixing a gear on a shaft of 27 mm diameter. The shaft is transmitting torque of 195,844 N.mm to the gear. The width of the key is equal 7 mm. The key is made of steel 50C4 (sy - 577 N/mm2) and the factor of safety is 3. For key material, the yield strength in compression can be assumed to be equal to the yield strength in tension. Determine...
Question: Analyse the efficiency of transmitting power using a solid shaft of diameter "d" compared to...

Question: Analyse the efficiency of transmitting power using a solid shaft of diameter "d" compared to a hollow shaft of diameters "Do" and "Di". The ratio "r" = Do/Di should be varied from 1.5, 1.6, 1.7, 1.8; 1.9; and 2.0 but the weight of the hollow shaft must be equal to the weight of the solid shaft. Assume the length of the shaft between the two bearings (see figure below) to be the same. must be until you find the...
A portion of a shaft where a gear is to be mounted has diameter of 50...

A portion of a shaft where a gear is to be mounted has diameter of 50 mm. The gear transmits 335 N-m of torque. The shaft is to be made of SAE 1040 cold-drawn steel. The gear is made from SAE 8650 OQT 1000 steel The width of the hub of the gear mounted at this location is 45 mm. Design the key. The standard key dimension for a 50-mm-diameter shaft would be 14mm '9 mm Q-1 a rectangular. Material...

1. If you have a 1.875" diameter shaft, what size key would you specify (H x...

1. If you have a 1.875" diameter shaft, what size key would you specify (H x W x L)?
3- The shaft shown in the figure rotates with constant angular velocity and is transmitting a...

3- The shaft shown in the figure rotates with constant angular velocity and is transmitting a torque from gear B to gear C through the forces Exo and Ez as shown. The shaft is subject to combined bending and torsion due to the forces shown. The weights of the shaft and pulleys may be neglected and the supports can exert only concentrated force reactions. The radius of the gear at B is 50 mm and that at C is 75...
Find the limits of the shaft and hole for the following basic size - fit combinations....

Find the limits of the shaft and hole for the following basic size - fit combinations. Chapter 7: Tolerancing1 Name: Date: P7-2) Find the limits of the shaft and hole for the following basic size -fit combinations. Basic Size 25 5 75 1 Fit 1 RC3 RC5 RC1 RC9 RC7 RC4 RC6 Fit 2 LC2 LC7 LC11 LC6 LC1 LC9 LC4 Fit 3 L LT5 LT6 LT3 1.375 2 2.125 LT1 LT2 LT3 LT4 Shaft Hole Basic Size Limits Shaft...

2. A nominal hole size of .6250 inch diameter and a RC6 class fit has been...

2. A nominal hole size of .6250 inch diameter and a RC6 class fit has been selected. Calculate the hole and shaft sizes and their tolerances. 3. A nominal hole size of 12 mm diameter and a H7/k6 class fit has been selected. Calculate the hole and shaft sizes and their tolerances