Please solve the following problem.
Please solve the following problem. 6-33 In Fig. 6-43, solve for , R R2, V2, V,...
Question 6 In the differential amplifier shown in Fig. Qu6, R1 = 10k 2, R2 = 10k 2, R3 = 100k 2 and Rf = 100K22. Determine the output voltage Vo if: Vol 12 0² 777 Figure Qu 6 (a) V1 = 5mV and V2 = 0 (b) V1 = 0 and V2 = 5m V (c) VI = 50mV and V2 = 25mV (d) V1 = 25mV and V2 = 50m V. [3x4 marks]
Good morning, I need help with the following, they all relate to OP Amps. Thanks in advance. 2 value 10.00 points Problem 05.010 An op amp voltage divider Find the voltage gain vo/vs of the circuit given below, where R1-18 kΩ and R2-14 k 2. 20 kΩ R1 1% R2 The voltage gain vo/vs of the circuit is Hints Referene eBook & Resources Hint#1 Check my work 3. 1000 points value Problem 05.025-Voltage follower Calculate the output voltage vo in...
For the circuit shown in Fig. 6, calculate:(a) the current in the 2.00−Ω resistor.(b) the potential difference between points a and b. Assume that the components on Fig. 7 have the following values:V1 = 10.0 V , V2 = 15.0 V , R1 = 5.0 Ω, R1 = 5.00 Ω, R2 = 10.0 Ω, R3 = 15.0 Ω, R4 = 20.0 Ω. (a) Find the current trough each branch of the circuit. (b) Find the power dissipated in each circuit...
R1-20 R2 30 1) In Fig. 6, V2 will be: a) 0.7v b) 1.5v c) 2.4v d) 5.0v e) 6.0v RS Fig. 6 2In Fig. 6, what minimum size (wattage) resistor should be used for R a) 1/8 b) 1/4 c) 1/2 d) 1W 2 w
Problem 2 a. Determine V.1.1, and le for the network Fig. 2.181 if R2 = 180 . b. Repeat part (a) if R, 470 . c. Determine the value of R, that will establish maximum power conditions for the Zener diode. d. Determine the minimum value of R, to ensure that the Zener diode is in the "on" state. 220 22 20 V V2 = 10 V Pz.. = 400 mW FIG. 2.181
Solve each practice problem. TYPE solutions in engineering notation TYPE solutions in engineering notation. Calculate the component voltages and branch currents for the circuit shown in Figure 6.40, along with the values of I, and Rr. 3. R3 2 kn R4 4.7 k R1 10 k Vs 26 V R5 3.3 k R2 3 kn FIGURE 6.40 Calculate the component currents and loop voltages for the circuit shown in Figure 6.42, along with the values of I and Rr 5....
Please answer clearly Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a) Voltage gain (Vo/vi) b) Input resistance (R) c) Output resistance (Ro) d) Maximum output voltage swing so as the amplifier stays in saturation mode. Assume VDD-20 V, R1-2.5 ΚΩ, R2-1KQ, R3-0.5 ΚΩ, R4-5 MQ, R5_1ΜΩ. R4 R1 R5 R2 Ro R3 Question 2 The amplifier shown in Figure 2 has the following parameters: Kn(W/L)-1 mA/V2, V-1 V Determine a)...
please show steps, and solve asap BEE 433 Electronic Circuit Design Problem Set #1 Due date: Answer the following problems and Circle the answers. 1.1 (Fig. 1.1 from the textbook) In the voltage amplifier circuit of Fig. 1.1, let vs = 100 mV, Rs = 100 k 52, Vi = 75 mV, RL = 10 S2, and vo = 2 V. If connecting a 30-S2 resistance in parallel with RL drops vo to 1.8 V, find Ri, A., and R....
ANSWER ALL PLEASE Question 20 2 pts In the Figure below, V1 = 14 V, V2 = 8 V, V3 = 10 V, R1 = 2.00, R2 = 4.0, and R3 = 2.00 Find the electric currents is, iz, and is. (Hint: use the junction a and the two loops). RI R 14 M4 Equations: Kirchoff's Junction (node) rule: 11 = 12 + iz Kirchoff's Loop rule (left loop): V1 - iRi - iz R2 + V2 = 0 Kirchoffs...
please show calculations and explanation when necessary In the circuit shown in Fig. 1, V = 120 V, R1 = 402, R2 = 209, and R3 = R1 = 109 a) What is the equivalent resistance of this circuit? b) What is the current through 13? c) What is the potential difference across R2? d) What is the total power used by this circuit? w RE ww R, RA Figure 1: Problem 1