if you have any doubts you can comment if you understand the solution give a thumbs up
Question 6 In the differential amplifier shown in Fig. Qu6, R1 = 10k 2, R2 =...
3) Find the output voltage for the circuit shown below. Rf 10K +12V DC R1 Vaw 2.2K IC1 UA741 Vb R2 W 2.2K -12V DC R3 Z RL 10K Fig 1 Differential amplifier using one opamp
Given below is a differential operational amplifier in block form and its internal transistor circuit with VCC=20V, VEE= 12 V , RC=5kΩ,RE=1kΩ and R1=2kΩ. Assume that the transistors are identical and have a βac=βdc=100. An ac signal Vi(t)=5sin(10t) is applied to the input terminals where Terminal 1 is Positive (non-invertinq) & Terminal 2 is negative (inverting) as stated in the cases below. Draw the output signals in each case. : a) V1=Vi(t) , V2=Grounded. Vo(t)=Vo2-Vo1 ) b) V1=Grounded , V2=Vi(t)....
R1 = 3k ; R2 = 4k ; Rf = 10k ; Rg = 8k ; V1 = 2V ; V2 = 0.5 V. This op amp is powered on a +/- rail. a. Solve for V+ (Voltage at the (+) input to the amplifier). Provide answer in Volts. b. Solve for V- (in Volts) c. Solve for IR1. Please give answer in mA. d. Solve for IRf. Please give answer in mA. e. What is the Gain (dB) for...
For the following multistage amplifier, find V2 if Vo=40 V, V1=0.2 V, R1=8.3 KO, R2=9.0 KA, R3=0.7 KA, R4=1.0 KN, R5=9.0 KO and RL=16.2 KN. R5 R1 + R4 Vo 14 + + V1 R2 w RL V2 R3 Answer:
For the following multistage amplifier, find V2 if Vo=40 V, V1=0.2 V, R1=8.3 K12, R2=9.0 K2, R3=0.7 KS2, R4=1.0 KN, R5=9.0 KN and RL=16.2 KA. R5 R1 w + R4 Vo 14 + V1 R2 RL V2 R3 We were unable to transcribe this image
For the following multistage amplifier, find V2 if Vo=40 V, V1=0.2 V, R1=12.0 K2, R2=9.0 KQ, R3=1.0 K, R4=1.0 K2, R5=9.0 K and RL=16.8 K. R5 R1 + R4 Vo 14 V1 R2 RL + V2 no R3 Answer: OV Consider the same circuit as above, but with the following parameters: if Vo=40 V, V1=0.2 V, V2=0.5V, R1=7.3 K2, R2=11.9 K2, R3=1.0 K, R4=0.8 K2, R5=10 K2 and RL=17 K2. What is the magnitude of the current 14 through resistor...
For the following multistage amplifier, find V2 if Vo=40 V, V1=0.2 V, R1=9.1 K12, R2=9.0 KN, R3=1.2 K12, R4=1.0 K12, R5=9.0 K12 and RL=16.1 K12. R5 R1 w w + R4 Vo 14 1 + v1 R2 RL + V2 win R3 Consider the same circuit as above, but with the following parameters: if Vo=40 V, V1=0.2 V, V2=0.5V, R1=8.3 KN, R2=9.8 K12, R3=1.0 KN, R4=1.1 K12, R5=10 KN and RL=21 KN. What is the magnitude of the current 14...
Design the circuit below using Multisim: Then adjust value of V1 and V2 from table below to find Vo: Please help me with this problem, thank you R3 100K +15 R2 V2 100K 6 Vo R1 5O-15 Џ 100K V1 Vi (V) V2 (V) +2 +5 +6 +5 +8 +5 +3 -1V +8 -2
For the amplifier circuits in Figs.3 and 7: a. Write an expression for the output voltage, vo, in terms of the resistor symbols and the input voltage, vin. ---For the first circuit (Fig. 3), the feedback resistor is the series combination of R2 and R3. Use both of these resistor symbols in your expression. -- For circuit 2 (Fig. 7), assume that vin = 5V and ignore potentiometer R1 and C3. b. Using resistor values and input voltage amplitudes, calculate...
Explain using theory, why does the simulation result is shown as followed Wheatstone Bridge + inverting amplifier Rf R1 R3 Rs VO R2 Rx Simulation condition 1. Parametric simulation (Vo vs R,) . Sweep AR (0-50(2) R3 R4 20k 20k ND 0 OU V1 R1 2 ND R5 R6 R7 1k uA741 GND 20k Rsweep) 20k R2 100k PARAMETERS 5.00v 4.98 4.96 4.94V 35 40 45 50 15 20 25 30 10 Rf R1 R3 Rs VO R2 Rx Simulation...