A screw jack has a screw thread 7.5 cm mean diameter and 1.5 cm pitch the...
A screw jack has a screw thread 7.5 cm mean diameter and 1.5 cm pitch the load on the jack revolves with the screw the coefficient of friction at the screw threads is 0.05 find the tangential force to be applied to the jack at 36 cm radius so as to lift a load
Homework Answers
Add Answer to:
A screw jack has a screw thread 7.5 cm mean diameter and 1.5 cm
pitch the...
A square power screw has a mean diameter of 30 mm and a pitch of 4...
A square power screw has a mean diameter of 30 mm and a pitch of 4 mm with single thread. The collar diameter can be assumed to be 35 mm. The screw is to be used to lift and lower a load of 7 kN. A coefficient of friction of 0.05 is to be used for friction at the thread and at the collar. Determine the following: (i) Torque required to raise the load. TR. (Equation 8.1) (ii) Torque required...
PROBLEM 5: Figure shows a screw jack lifting a non- rotating load of 200 kg. The...
PROBLEM 5: Figure shows a screw jack lifting a non- rotating load of 200 kg. The screw jack consists of a single square screw thread with a major diameter of 30 mm and 10 threads per 5 cm. A rotating nut, driven by a leverage arm moves a plain thrust collar with diameter de 50 mm, which in turn lifts and lowers the load. The friction coefficient between the nut and the collar μ -0.25 and the friction coefficient between...
Question 1 (10 pts) A square-threaded, single thread power screw with a mean diameter of 1...
Question 1 (10 pts) A square-threaded, single thread power screw with a mean diameter of 1 in and four threads per inch is used to raise a load of 25,000 lb. The collar mean diameter is 1.5 in. The coefficient of friction is 0.1 for both the thread and the collar. Determine the following: Load 25,000 lb Q1.1. Determine the major diameter of the screw (2pts) Q1.2. Determine the screw torque required to raise the load (2pts) Q1.3. Determine the...
2. The C clamp shown in the figure below uses an Acme thread screw. The screw...
2. The C clamp shown in the figure below uses an Acme thread screw. The screw has a diameter of 17 mm and a pitch of 5 mm. The frictional coefficients are 0.15 for the threads and 0.20 for the collar. The collar, which in this case is the anvil striker's swivel joint, has a friction diameter of 25 mm. Find the clamping force if 105 N force applied to the handle at a distance of 100 mm from the...
A square-threaded power screw with single thread is used to raise a load of 25,000 lb....
A square-threaded power screw with single thread is used to raise a load of 25,000 lb. The screw has a mean diameter of 1-in. and four threads per inch. The collar mean diameter is 1.5 in. The coefficient of friction is estimated as 0.1 for both the thread and the collar. Assume the length of thread engagement is 1.5 times the outside diameter of the screw. 1. Calculate the safety factor for the power screw to fail in torsion. Assume...
4. A single-start, square-threaded power screw has the following baseline character- istics: Outside diameter pitch, p...
4. A single-start, square-threaded power screw has the following baseline character- istics: Outside diameter pitch, p Load, W 25.4 mm 5.08 mm 1500 N thread friction coefficient 0.08 collar friction coefficient collar diameter 0.04 28 mm (a) What torque, TR, total, is required to raise the load? Include units. (b) What torque, TL, total, is required to lower the load? Include units (c) Suppose the screw runs at 100 rpm for ten seconds, raising the load. How much energy is...
1. A single-threaded ACME power screw has a major diameter d=1.25 in with a pitch of...
1. A single-threaded ACME power screw has a major diameter d=1.25 in with a pitch of 0.2 in. The threaded coefficient of friction u is 0.2, and the coefficient of collar friction He is 0.15. The mean collar diameter de is 2 in. The external load on the screw is 1200 lb. Find: a) The torque required to raise the load. b) The maximum nominal shear stress of the screw body.
The position of the automobile jack shown is controlled by a screw ABC that is single...
The position of the automobile jack shown is controlled by a
screw ABC that is single threaded at each end
(right-handed thread at A, left-handed thread at
C). Each thread has a pitch of 2.5 mm and a mean diameter
of 10 mm. If the coefficient of static friction is 0.15, determine
the magnitude of the couple M that must be applied
to raise the automobile.
3500 N D С М А 30° В 30° E
There are two jack screw assemblies both with an ISO Metric Trapezoidal ‘Tr 16 x 3’ screw, one single-thread and the oth...
There are two jack screw assemblies both with an ISO Metric Trapezoidal ‘Tr 16 x 3’ screw, one single-thread and the other double-thread, to raise and lower a load of 450 kg. A ball-thrust bearing forms part of the assembly and therefore collar friction is negligible. The coefficient of sliding friction for both screws is 0.08. (a) For each assembly, determine: (i) the pitch, pitch diameter, lead and lead angle; (ii) the running torque required to lower the load; (iii)...
1) [20 pts] Power screw geometry A power screw is 26 mm in diameter and has...
1) [20 pts] Power screw geometry A power screw is 26 mm in diameter and has a thread pitch of 5 mm. a) Find the thread depth, the thread width, the mean and root diameters, and the lead for square threads. The thread depth is The thread width is The mean diameter is The root diameter is The lead is mm. b) Find the thread depth, the thread width, the mean and root diameters, and the lead for Acme threads....
A square power screw has a mean diameter of 30 mm and a pitch of 4 mm with single thread. The collar diameter can be assumed to be 35 mm. The screw is to be used to lift and lower a load of 7 kN. A coefficient of friction of 0.05 is to be used for friction at the thread and at the collar. Determine the following: (i) Torque required to raise the load. TR. (Equation 8.1) (ii) Torque required...
PROBLEM 5: Figure shows a screw jack lifting a non- rotating load of 200 kg. The screw jack consists of a single square screw thread with a major diameter of 30 mm and 10 threads per 5 cm. A rotating nut, driven by a leverage arm moves a plain thrust collar with diameter de 50 mm, which in turn lifts and lowers the load. The friction coefficient between the nut and the collar μ -0.25 and the friction coefficient between...
Question 1 (10 pts) A square-threaded, single thread power screw with a mean diameter of 1 in and four threads per inch is used to raise a load of 25,000 lb. The collar mean diameter is 1.5 in. The coefficient of friction is 0.1 for both the thread and the collar. Determine the following: Load 25,000 lb Q1.1. Determine the major diameter of the screw (2pts) Q1.2. Determine the screw torque required to raise the load (2pts) Q1.3. Determine the...
2. The C clamp shown in the figure below uses an Acme thread screw. The screw has a diameter of 17 mm and a pitch of 5 mm. The frictional coefficients are 0.15 for the threads and 0.20 for the collar. The collar, which in this case is the anvil striker's swivel joint, has a friction diameter of 25 mm. Find the clamping force if 105 N force applied to the handle at a distance of 100 mm from the...
4. A single-start, square-threaded power screw has the following baseline character- istics: Outside diameter pitch, p Load, W 25.4 mm 5.08 mm 1500 N thread friction coefficient 0.08 collar friction coefficient collar diameter 0.04 28 mm (a) What torque, TR, total, is required to raise the load? Include units. (b) What torque, TL, total, is required to lower the load? Include units (c) Suppose the screw runs at 100 rpm for ten seconds, raising the load. How much energy is...
1. A single-threaded ACME power screw has a major diameter d=1.25 in with a pitch of 0.2 in. The threaded coefficient of friction u is 0.2, and the coefficient of collar friction He is 0.15. The mean collar diameter de is 2 in. The external load on the screw is 1200 lb. Find: a) The torque required to raise the load. b) The maximum nominal shear stress of the screw body.
The position of the automobile jack shown is controlled by a
screw ABC that is single threaded at each end
(right-handed thread at A, left-handed thread at
C). Each thread has a pitch of 2.5 mm and a mean diameter
of 10 mm. If the coefficient of static friction is 0.15, determine
the magnitude of the couple M that must be applied
to raise the automobile.
3500 N D С М А 30° В 30° E
1) [20 pts] Power screw geometry A power screw is 26 mm in diameter and has a thread pitch of 5 mm. a) Find the thread depth, the thread width, the mean and root diameters, and the lead for square threads. The thread depth is The thread width is The mean diameter is The root diameter is The lead is mm. b) Find the thread depth, the thread width, the mean and root diameters, and the lead for Acme threads....
Most questions answered within 3 hours.
-
Lincoln, Inc., which uses a volume-based cost system, produces
cat condos that sell for $170 each....
asked 36 seconds ago -
On November 3, the spot price for cotton was $0.81/lb., and the
February futures price was...
asked 1 minute ago -
Using Python:
A Prime number is an integer greater than 1 that cannot be
formed by...
asked 23 minutes ago -
Read about Cokes strategy in Africa in the article below and
discuss the ethics of selling...
asked 10 minutes ago -
What made of a 40.0% NaOH solution should be diluted to 1.00 L
with water to...
asked 10 minutes ago -
Draw and describe the results of the Meselson-Stahl experiments
showing that DNA replication followed the Semi-conservative...
asked 15 minutes ago -
Deeply Explain the Following Web Development Softwares Along
With the Reasons to Choose them For Development....
asked 12 minutes ago -
essay question: why was Hurricane Katrina so devastating? How
and why did the levees break in...
asked 17 minutes ago -
Why might it be necessary to reduce consumer spending in order
to attain faster economic growth?...
asked 26 minutes ago -
Express your answer with the appropriate units.
1. How many milliliters of oxygen gas at STP...
asked 32 minutes ago -
A
solution is prepared by mixing 0.12L of 0.11 M sodium chloride with
0.26 L of...
asked 33 minutes ago -
Difference between follicle and egg.
Where exactly are LH and FSH located on the ovaries?
What...
asked 34 minutes ago