Answer is 11892.8572 lbmass / hr
Question 2 (5 points) The flowrate of methyl acetate in a methanol-methyl acetate mixture containing 16.0...
A mixture of 75 mol% methanol and 25 mol% methyl acetate is fed to a flash evaporator. The feed stream (liquid) is at 20 °C The flash evaporator runs at 55 °C, 90 kPa. What is the energy input required to operate this flash evaporator? ln(
A solution of methyl acetate (C3H60 2) and water that is 25.% methyl acetate by mass is boiling at 94.7 °C. The vapor is collected and cooled until it condenses to form a new solution. Calculate the percent by mass of methyl acetate in the new solution. Here's some data you may need: normal boiling point density vapor pressure at 94.7 °C methyl acetate 57. °C 0.93 mL 2360. torr water 100. °C 1.00 mL 630. torr Be sure your...
(10 points) A mixture containing 25% mass percent of CH4 and 75% mass percent of C2Hs into a tank at a rate of 106 kg/hr. (CHs: 16 g/mol; C2H6: 30 g/mol) a. What is the molar flow rate of the mixture? (5 points) b. What is the molar percentage of CH4 in the mixture? (5 points)
Question 27 (2 points A gaseous mixture containing 250 mol Ar and 346 mol O2 ius a total pressure of 4283 on What is the partial pressure of CO2? 0.782 atm 05 10 27 aded Page 2 2 1.95 atm Page 3: C 16.0 atm 3 (2.70 atm
please help with organic chemistry! mechanisms?
5) The reaction of 2-bromo-1,1-dimethylcyclohexane with methanol gives the following products. Please provide a detailed explanation to the formation of each product. You should use structures of intermediates in your answer. (8 points). осн, CH,он OCH Br + 6) There are a variety of isomeric 1,2,3,4,5,6-hexachlorocyclohexanes, but one of them does not react with CH3CH20' to give an elimination product. Provide the structure of this compound and briefly explain why it does not react...
Question 15 5 pts The reaction mixture for the synthesis of methyl benzoate is heated for about an hour. The purpose of this is: To increase the reaction yield To increase the rate of the reaction. To decompose side products To evaporate some of the solvent.
Attempt 1 Question 14 of 15 > A 0.690 g mixture containing only sodium chloride and potassium chloride was dissolved in water. It required 34.8 mL of 0.317 M AgNO, to completely precipitate all of the chloride present. What is percent composition by mass of sodium chloride and potassium chloride in the mixture? mass percent NaCl : 64.2 mass percent KCI : 35.9
2. A solution containing a mixture of naphthalene, benzoic acid, and benzaldehyde is analyzed via TLC and GC. Use the structures and properties of the compounds to aid in answering the following questions. A. In the TLC experiment, the mixture is spotted on a silica TLC plate and eluted with a 1:1 mixture of hexanes and ethyl acetate. Three spots are observed on the plate, with Re values of 0.25, 0.58, and 0.74. Indicate which spot corresponds to which compound....
9.3. Calculate the mass flux of methanol in water at 77°F (2=4.95 x 10-5 ft2/hr). The concentrations of meth- anol at two points 0.1 in. apart are 0.05 and 0.10 lb molelft?.
Question 5 2/2 points A 3.7602 g sample of an unknown salt containing ferrous ion was dissolved and diluted to 250.0 ml. Repeat 25.00 mL samples of the total solution were titrated with 0.01221 M KMNO4 solution, and the mean of three accepted corrected titration volumes was 13.36 mL. Calculate the %w/w of iron in the original sample mass. State your answer to 2 places after the decimal place. Do not enter units.