This is a part of the final for telecommunication. I'm lost on these questions and would really appreciate if you could show all work. Thanks in advance.
This is a part of the final for telecommunication. I'm lost on these questions and would...
The sinusoidal modulating wave is applied to a phase modulator with phase sensitivity kp. The unmodulated carrier wave has frequency fc and amplitude Ac. a) Determine the spectrum of the resulting phase-modulated signal, assuming that the maximum phase deviationP4es not exceed 0.3 radians. b) Construct a phasor diagram for this modulated signal, and compare it with that of the corresponding narrow-band FM signal. The sinusoidal modulating wave is applied to a phase modulator with phase sensitivity kp. The unmodulated carrier...
1 2 4. The amplitude modulation signal is given by the following expression and is applied to 75 load. Vam(t) = 10 sin (21fct) - 2.5 cos (1500krt) + 2.5 cos (1450krt) V Determine: a) Modulation index b) The frequency of the carrier and the information signal c) The bandwidth d) The total power e) The transmission power efficiency be ar e 5. One of the inputs to a frequency modulator is a 250 kHz carrier signal with amplitude of...
Engineering question. Please provide your work. Please explain how you got each number in your work. Please do not copy your work and answers from other people's links. Amplitude modulation (AM) An AM signal has the following parameters: 1. - a carrier amplitude of 60 volts; - a carrier frequency, fe of 1560 kHz; - a modulating frequency of 13 kHz; - a modulation index, m, of 0.707 (a) What are the lower and upper side frequencies in kHz? (b)...
3(a) A complex signal given by the expression cos (9t x 103t) Vm(t) %3D 0.5cos(Зл х 103t) + сos(8т х 103t) + is used to amplitude modulate a carrier signal, Vc(t) = 3cos(2n shown in Figure 3(a) 105t) as X Vm(t) 0.5cos(3t x 103t) cos(8T x 103t) AM Modulator AM Signal cos(9t x 10t) Vc(t) 3cos(2n x 105t) Figure 3(a) The AM signal in Question 3(a) is developed across 2.2 kn load resistance The modulated carrier in Question 3(a) is...
()=< a) Consider the case where a modulating tone v, a cos(2ft) is used in a Double Side Band m Amplitude Modulation (DSC-AM) scheme whose varying with time carrier amplitude is [K+a cos(2ft Provide the equation of the modulated carrier signal v (t and then derive from that an expression that shows the spectral components of v (t). Furthermore provide the phasor representation of DSB-AM. Now consider the case of Double Side Band Suppressed carrier AM and provide both the...
12. An FM signal has a deviation of 3 kHz and a modulating frequency of 1 kHz. Its total power Pris 5 W, developed across a 50 2 resistive load. The carrier frequency is 160 MHz (a) Calculate the RMS signal voltage VI (b) Calculate the RMS voltage at the carrier frequency and each of the first three sets of sidebands. (c) For the first three sideband pairs, calculate the frequency of each sideband. (d) Calculate the power at the...
a. In FM transmission circuits, explain the purpose and function of: i. Pre-emphasis and de-emphasis circuits. (CO1: PO1 - 3 Marks) ii. Limiter circuit. (CO1: P01 - 3 Marks) b. A sinusoidal carrier wave of frequency fe = 110 MHz is modulated by a modulating signal m(t). The characteristics of the modulating signal is illustrated in Figure Q2(b) and the Frequency Deviation Constant of the FM Modulator, kf = 107 Hz/volt. Determine the minimum bandwidth required for transmission of the...
[15 points] You are asked to design a DSB-SC AM modulator to generate a modulated signal km(t)cos(wt+0), where m(t) is a signal band-limited to B Hz. The following figure shows a DSB- SC AM modulator available in the stockroom. The carrier generator available generates not cos(wct), but cos (wct). Explain whether you would be able to generate the desired signal using only this equipment. You may use any kind of filter you like. 3. What kind of filter is required...
signals and communications 2 Make sure you show all working and describe each step in your calculations. 1. A signum function is defined as sgn(t) = { 1、12 0 1 t<0 Plot and express this function in terms of the unit-step function. 5 marks/ Determine and plot the even and odd parts of the signal 2. x(t) (te-3 +2)u(t). 5 marks 3. If prove that y[n-m] = x[n-m] * h[n]. 5 marks 4. Assuming α > 0, plot the signal...
Please help me fill out this page I'm so lost. Please explain too, thank you! рр 0,43 2.dl 3.01 Code Number . STRUCTURE OF UNKNOWN (Draw Below) -. PROTON MAGNETIC RESONANCE SPECTRAL DATA Complete the table below by listing the chemical shifts of all of the signal patterns in the nmr spectrum of your compound (chemical shifts of clear multiplets are single numbers at the midpoint of the pattern, chemical shifts of complex multiplets are given as ranges). Assign the...