up 200 N/M, 1500 N/m For the beam and loadings shown below, and if the beam...

Question

Question

For the beam and loadings shown below, and if the beam has a rectangular cross section (4x6 cm), determine the maximum value

up 200 N/M, 1500 N/m

Answer 1

Answer #1

2000)-の 200 Non 150 N ABSOLDTE VALUE of -60ON 2 = 5oo.coo Pa 0,5 MPa

Answer 2

Similar Homework Help Questions

A rectangular beam is subjected to the loadings shown in Figure Q.16(a) has cross section of...

A rectangular beam is subjected to the loadings shown in Figure Q.16(a) has cross section of 100 mm x 300 mm as shown in Figure Q.16(b). An axial load of 5 kN is applied along the centroid of the cross-section at one end of the beam. Compute the normal stress and shear stress at point P through the cut-section of P in the beam. [15 marks] у 10 kN/m P Ž 5 KN --- 00 P k 3 m -...
5. (20 Points) For the loading on the simply supported beam shown below. a) What is...

5. (20 Points) For the loading on the simply supported beam shown below. a) What is the internal shear and bending moment at point C? b) Given the beam has a rectangular cross section with a width of 8 in. and a height of 20 in., find the maximum normal stress (om) in the cross section at C from the bending moment calculated above. 600 lb 200 lb/ft
The beam has the rectangular cross section shown. If w 1 kN/m

The beam has the rectangular cross section shown. If w 1 kN/m, determine the maximum bending stress in the beam. Sketch the stress distribution acting over the cross section.

A beam of rectangular cross section 200 mm deep and 100 mm wide. If the beam...

A beam of rectangular cross section 200 mm deep and 100 mm wide. If the beam is 3m long, simply supported at either end and carries point loads as shown in FIGURE 2 (on page 4). 2. SAN 1OAN R, FR 100mm FIG.2 (a) Calculate the maximum bending moment (b) Calculate the maximum stress in the beam (c) At the point of maximum stress sketch a graph of the stress distribution through the thickness of the beam, indicating which are...
A beam is loaded by a shear force V. The beam cross-section is shown below. The...

A beam is loaded by a shear force V. The beam cross-section is shown below. The moment of inertia of the cross-section is 347.1 in4. The centroid of the cross-section is 6.25 inches from the base. Determine: a) the shear stress at point A. b) the shear stress at point B. c) the maximum shear stress in the cross-section. V = 50 (kips) The maximum shear stress at point A is _____(ksi) The maximum shear stress at point B is...
For the beam shown in the figure below a. Draw the shear and moment diagrams for this beam

For the beam shown in the figure below a. Draw the shear and moment diagrams for this beam b. Calculate the maximum bending stress, maximum axial stress, and maximum shear stress acting on the beam cross section c. Sketch the distributions of shear stresses and bending stresses acting on the beam cross section at the locations where these stresses are maximum.

The figure shown below is the cross section of a steel rectangular beam. The beam is subjected to transverse loading ap...

The figure shown below is the cross section of a steel rectangular beam. The beam is subjected to transverse loading applied in the Y-direction. Mark the location on the cross section that experiences maximum normal stress. FE CIVIL PRACTICE EXAM The figure shown below is the cross section of a steel rectangular beam. The beam is subjected to 64. transverse loading applied in the Y-direction Mark the location on the cross section that experiences maximum normal stress SIDE VIEW CROSS...
The beam has a rectangular cross section and is made of wood having an allowable

The beam has a rectangular cross section and is made of wood having an allowable (transverse) shear stress of 200 psi. Determine the maximum shear force V that can be permitted by the cross section of the beam.
IR 2 2. (20 pts.) The below beam is loaded by three different loads as shown....

IR 2 2. (20 pts.) The below beam is loaded by three different loads as shown. The cross-section of the beams consists of a t-shped member whose dimensions are shown below. The centroid of the cross-section is located at 8 inches from the base of the cross- section and the moment of inertia of the cross-section is 814 in 4 a) Draw the shear diagram for the beam. Submit that information through ELC. Label all points. b) determine the maximum...

The beam has the rectangular cross section shown.

The beam has the rectangular cross section shown.Part A If w = 3kN/m, determine the maximum bending stress in the beam. Wood used for the beam has an allowable bending stress of ơ=6MPa (Figure 1) Part A Determine the minimum dimension d of the beams cross sectional area.