Homework Answers
Add Answer to:
ECE 624 Homework 5 Problem 5 In a boost converter, the input voltage is 220 V...
Design a buck converter with the following specifications: Input voltage = 311 V Output voltage =...
Design a buck converter with the following specifications: Input voltage = 311 V Output voltage = 48 V Output voltage ripple = +/- 0.1% Maximum output current = 10 A Inductor current ripple = 5% Switching frequency = 100 kHz a) Select the inductor and the output capacitor and show a capture of the behaviour b) Calculate power losses assuming a rising time of 100 ns, a falling time of 100 ns, and Rdson = 10 mΩ. c) Calculate output...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 ...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
A boost converter has an input of 5 V and an output of 25 W at...
A boost converter has an input of 5 V and an output of 25 W at 15 V. The minimum inductor current must be no less than 50 percent of the average. The output voltage ripple must be less than 1 percent. The switching frequency is 300 kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value.
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage...
A Buck-boost converter has an output voltage 100 V, output power 60 W and input voltage 12 V. Switching frequency is 15 kHz. Calculate duty ratios for the switch and the diode. Find values for the inductor L and capacitor C, when the allowed output voltage ripple is ±0.15 % and the inductor current ripple is ±1 % (of the average value). If the on-time of the switch has an inaccuracy of ±50 ns, what is the new output voltage...
2. A portable fan needs a 5 V input voltage from two AA batteries connected in...
2. A portable fan needs a 5 V input voltage from two AA batteries connected in series. Each AA battery consists of a voltage ranging between 1.2 V and 1.8 V. Consider a boost converter with specifications as follows : Switching frequency = 200 kHz, Output current = 10 mA to 300 mA Assuming the converter has to be operated in continuous conduction mode for all time, design the inductor for this converter.
Please help in this question conserning the buck-boost converter 4. a. Draw a buck-boost converter to...
Please help in this question conserning the buck-boost
converter
4. a. Draw a buck-boost converter to be implemented with an IGBT and diode b. Suggest suitable component values if such a converter is to serve resistive loads between 15 W and 30 W with a constant 8 V output, when the converter's input can vary between 5 V and 12 V. The output peak-to-peak voltage ripple should be less than 5% of the output voltage. The converter should operate in...
Q5. 5.a. Sketch the circuit arrangement of a DC-DC boost (step up) converter, clearly labelling each...
Q5. 5.a. Sketch the circuit arrangement of a DC-DC boost (step up) converter, clearly labelling each circuit element [4 тarks] [Refer to lecture notes] Sketch all significant operating waveforms for this converter for continuous conduction conditions over two switching periods, in particular showing 5.b. the voltage across the main switching device and the boost diode. [2 marks the voltage across the inductor [3 тarks] the current flowing through the inductor [3 marks [Refer to lecture notes] 5.c. The DC-DC boost...
of CM with Consider the flyback converter with DC input voltage Vd of 48v. The output...
of CM with Consider the flyback converter with DC input voltage Vd of 48v. The output voltage is regulated to 5V and the turn's ratio transformer is considered as 6:1. The magnetizing inductance of the transformer is 150?H The converter is operated in C a switching frequency of 200 kHz with the load power of 30W. Assuming the converter to be lossless, calculate b. switch voltage stress neglecting the leakage inductance of the transformer
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its...
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Problem 1: (40 points) A boost converter based power factor correction circuit needs to operate with...
Problem 1: (40 points) A boost converter based power factor correction circuit needs to operate with universal input voltage, i.e the input voltage can be either 120V (RMS)+/- 10% at 60 Hz or 240 V(RMS) +/- 10% at 50 Hz. The output voltage is regulated at 400 V DC and the maximum (average) output power is 1kW. The switching frequency is 200 kHz. (a) Calculate the value of inductance needed to keep its peak peak ripple current to be less...
2. Renewable energy system requires a boost converter with input voltage variation of 18 V to 42 V (de) and gives output of 120 V at 0.6 kW. For the converter the switching frequency is set at 50 kHz. a) Find the operating duty cycle range for each switch of the converter0 marks b) 196 What is the inductor value which should keep inductor current variation below under all input voltages [30 marks] c) Find the capacitor value which should...
Please help in this question conserning the buck-boost
converter
4. a. Draw a buck-boost converter to be implemented with an IGBT and diode b. Suggest suitable component values if such a converter is to serve resistive loads between 15 W and 30 W with a constant 8 V output, when the converter's input can vary between 5 V and 12 V. The output peak-to-peak voltage ripple should be less than 5% of the output voltage. The converter should operate in...
Q5. 5.a. Sketch the circuit arrangement of a DC-DC boost (step up) converter, clearly labelling each circuit element [4 тarks] [Refer to lecture notes] Sketch all significant operating waveforms for this converter for continuous conduction conditions over two switching periods, in particular showing 5.b. the voltage across the main switching device and the boost diode. [2 marks the voltage across the inductor [3 тarks] the current flowing through the inductor [3 marks [Refer to lecture notes] 5.c. The DC-DC boost...
of CM with Consider the flyback converter with DC input voltage Vd of 48v. The output voltage is regulated to 5V and the turn's ratio transformer is considered as 6:1. The magnetizing inductance of the transformer is 150?H The converter is operated in C a switching frequency of 200 kHz with the load power of 30W. Assuming the converter to be lossless, calculate b. switch voltage stress neglecting the leakage inductance of the transformer
1) (6 points) It is desired to design a 50 W buck-boost converter to regulate its output voltage at 26V from a solar panel whose output voltage varies between 20 and 40 V. The desired switching frequency is 20 kHz. The ripple current in the inductor should remain within +/-0.1 A, and the output voltage ripple should not exceed +/- 2%. a. Determine the duty cycle range for operating this converter. b. Design this buck-boost converter by finding lower limits...
Problem 1: (40 points) A boost converter based power factor correction circuit needs to operate with universal input voltage, i.e the input voltage can be either 120V (RMS)+/- 10% at 60 Hz or 240 V(RMS) +/- 10% at 50 Hz. The output voltage is regulated at 400 V DC and the maximum (average) output power is 1kW. The switching frequency is 200 kHz. (a) Calculate the value of inductance needed to keep its peak peak ripple current to be less...
Most questions answered within 3 hours.
-
If you titrated 30.0 mL of 0.1 M HCl with 0.1 M NaOH, indicate
the approximate...
asked 2 minutes ago -
NADH passes electrons into the electron transport chain. List
the carriers that would receive the electrons,...
asked 10 minutes ago -
A cylindrical cable with a resistivity of 1.6x10-8 Ω·m and cross
sectional area of 3x10-5 m^2...
asked 10 minutes ago -
True or False.
A consumer with convex preferences who is indifferent between
the bundles (5,2) and...
asked 14 minutes ago -
A diamond's index of refraction for red light, 656 nm, is 2.410,
while that for blue...
asked 27 minutes ago -
Compare HPLC, SPE, and GC. Identify the differences, the
advantages, and the weaknesses of each method.
asked 28 minutes ago -
Characteristic x-rays emitted by potassium have a wavelength of
0.374 nm. What is the energy of...
asked 31 minutes ago -
there is a function to create two random numbers between 1 and
25 and a function...
asked 49 minutes ago -
At a certain temperature, the ?pKp for the decomposition of
H2SH2S is 0.832.0.832.
H2S(g)↽−−⇀H2(g)+S(g)H2S(g)↽−−⇀H2(g)+S(g)
Initially, only...
asked 43 minutes ago -
Part 1.C&A Fast Food has four activities in serving a
customer: greet customer, take order, process...
asked 49 minutes ago -
Which attribute allows you to specify a custom "thumbnail" for
multimedia elements?
asked 1 hour ago -
How much 0.1200 M sodium hydroxide solution is need to titrate
14 mL of a 0.100...
asked 1 hour ago