A sample of gas is caused to go through the cycle shown in the pV diagram...

Question

Question

Answer 1

Answer #1

Dear student,

Find this solution.if any issue with that don't forget to write in comment section.I will rectify them as soon as possible.

If you find the solution helpful and kindly RATE THE ANSWER it would be appreciated.

Your rating is important to me.

Thanks for asking.. we know Area Under Pv qraph gives PPA) 0ok-dane 3 t 2 Area= wak dane Under cyde. basex height 3 x 2X10 Optian ()is cameet

Answer 2

Similar Homework Help Questions

ANSWER ALL PARTS As shown in the pV diagram, an ideal gas moves through a cycle...

ANSWER ALL PARTS As shown in the pV diagram, an ideal gas moves through a cycle from A to B to C and then back to A. From state A to state B, the ideal gas absorbs 80.0 J of heat and its internal (i.e. its thermal) energy increases by 30.0 J. From state B to state C, the internal energy of the ideal gas decreases by 20.0 J. As such, determine the following quantities: B V The work done...
A heat engine takes for 0.40 mol of ideal H2 gas around the cycle shown in the pV- diagram.

A heat engine takes for 0.40 mol of ideal H2 gas around the cycle shown in the pV- diagram.Ta=400KTb=800KTc=592K Process a→b is at constant volume, process b→c is adiabatic, and process c-> a is at constant pressure of 2 atm. The value of y for this gas is 1.40. (a) Find the pressure and volume at points a, b and c (b) Calculate Q, W, and AU for each of the processes. (c) Find the net work done by the gas in the cycle (d)...
A heat engine using a monatomic gas follows the cycle shown in the pV diagram. P11...

A heat engine using a monatomic gas follows the cycle shown in the pV diagram. P11 The gas starts out at point 1 with a volume of V1 = 318 cm", a pressure of p1 = 147 kPa, and a temperature of 317 K. The gas is held at a constant volume while it is heated until its temperature reaches 455 K (point 2). The gas is then allowed to expand adiabatically until its pressure is again 147 kPa (point...

2) Sketch a PV diagram and find the work done by the gas during the following...

2) Sketch a PV diagram and find the work done by the gas during the following stages. (a) A gas is expanded from a volume of 1.0 L to 6.0 L at a constant pressure of 8.0 atm. _ J (b) The gas is then cooled at constant volume until the pressure falls to 1.5 atm. J (c) The gas is then compressed at a constant pressure of 1.5 atm from a volume of 6.0 L to 1.0 L. (Note:...
A heat engine takes 0.262 mol of a diatomic deal gas around the cycle shown in the pV-diagram bel...

A heat engine takes 0.262 mol of a diatomic deal gas around the cycle shown in the pV-diagram below. Process 1 → 2 is at constant volume, process 2-) 3 is adiabatic, and process 3-1 is at a constant pressure of P = 2.00 atm. The value of r for this gas is 1.4 2,7-600K T,-300 K T, 492 K 0 (a) Find the pressure and volume at points 1, 2, and 3. pressure (Pa) volume (m3) point 1 point...
is no work done, by the gas or the surroundings. Need Help? Sketch a PV diagram...

is no work done, by the gas or the surroundings. Need Help? Sketch a PV diagram and find the work done by the gas during the following stages. (a) A gas is expanded from a volume of 1.0 L to 7.0 L at a constant pressure of 5.5 atm. (b) The gas is then cooled at constant volume until the pressure falls to 1.5 atm (c) The gas is then compressed at a constant pressure of 1.5 atm from a...

When a gas follows path 123 on the PV diagram in the figure below, 424 J...

When a gas follows path 123 on the PV diagram in the figure below, 424 J of energy flows into the system by heat and -166 J of work is done on the gas. (a) What is the change in the internal energy of the system? J (b) How much energy Q flows into the system if the gas follows path 143? The work done on the gas along this path is -63.0 J. J (c) What net work would...
When a gas follows path 123 on the PV diagram in the figure below, 419 J...

When a gas follows path 123 on the PV diagram in the figure below, 419 J of energy flows into the system by heat and −171 J of work is done on the gas. A rectangular path is plotted on a PV diagram that has a horizontal axis labeled V, and a vertical axis labeled P. The vertices of the rectangle, starting from the bottom-left corner and continuing clockwise, are labeled in the following order: 1, 2, 3, 4. The...
An ideal gas initially at P., V., and is taken through a cycle as shown below....

An ideal gas initially at P., V., and is taken through a cycle as shown below. (Let the factor n = 2.7.) Р nP; (a) Find the net work done on the gas per cycle for 2.75 mol of gas initially at 0°C. -23.05 How much work is done on the gas as it goes from A to B and as it goes from C to D? kJ (b) What is the net energy added by heat to the system...