Homework Answers
Problem 3 Statically Indeterminate Axially Loaded Members (25pts) The assembly shown consists of rigid bar ABC,...
Problem 3 Statically Indeterminate Axially Loaded Members (25pts) The assembly shown consists of rigid bar ABC, two fiber-reinforced plastic (FRP) rods (1) and (3), and FRP post (2). The modulus of elasticity for the FRP is E = 18 GPa. Determine the vertical deflection of joint D relative to its initial position after the 30 kN load is applied. 2.4 m 1.8 m Rigid bar | B |(2) (3) || 3.0 m 3.6 m A = 500 mm? Az= 500...
A uniformly-distributed load wis supported by a structure consisting of rigid bar BDF and three rods....
A uniformly-distributed load wis supported by a structure consisting of rigid bar BDF and three rods. Rods (1) and (2) are 17-mm-diameter stainless steel rods that have an elastic modulus of E = 199 GPa. Rod (3) is a 23-mm-diameter bronze rod that has an elastic modulus of E = 101 GPa. Use a = 1.5 m and L = 3.1 m. For a load magnitude of w = 36 kN/m, calculate (a) the normal stress in each rod. (b)...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the ver...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
Chapter 3, Reserve Problem 122 The rigid bar AC is supported by two axial bars (1)...
Chapter 3, Reserve Problem 122 The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 × 10-mm/mm/°C]. The cross-sectional area of bar (1) is A1 = 236 mm2 and the cross- sectional area of bar (2) is Az = 389 mm2. After load P has been applied and the temperature of the entire assembly has increased by 26°C, the total strain in bar...
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars...
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 x 10-6 mm/mm/°C). The cross-sectional area of bar (1) is A1 = 226 mm- and the cross-sectional area of bar (2) is Az = 362 mm. After load P has been applied and the temperature of the entire assembly has increased by 22°C, the total strain in bar (2) is measured as 1020...
1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m...
1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. What is the Poisson's Ratio of this material? 2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length...
The three-bar truss ABC shown in the figure has a span L = 3 m and...
The three-bar truss ABC shown in the figure has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm and modulus of elasticity E = 200 GPa. A load P acts horizontally to the right at joint C. (a) If P= 500 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load Pox if the displacement of joint B is limited to 2.5mm? 45 45°...
practice exam for mechanic of material Problem #3: The rigid be m The rigid beam ACE...
practice exam for mechanic of material
Problem #3: The rigid be m The rigid beam ACE is u sed the suspender bars. Bars AB der hars Bars AB and EF are made of aluminum and har CD is made of steel. Each barha and bar CD is made of steel Fach har has a cross-sectional area of 900 mm, Ex - 200 GPa, E-70 GPa P-20 KN. al 2 m 5 -15 Fox 190 0 3 FAQ +15 Foc 390...
3- (SKMMIH3/SME2113) from plastic having modulus of elasticity, E-4.0GPa a) Bar ABCD shown in Figure Q3a is made The bar consists of three segments, AB, BC, and CD. Segment AB is hollow and segm...
3- (SKMMIH3/SME2113) from plastic having modulus of elasticity, E-4.0GPa a) Bar ABCD shown in Figure Q3a is made The bar consists of three segments, AB, BC, and CD. Segment AB is hollow and segments BC and CD are solids If the shortening (contraction) of bar ABCD is limited to 4.0 mm, determine the maximum allowable force P to be applied at C. (8 marks) 90 mm ΟΙ 00 mm 1080 min PL 500 mm 250 mm 250 mm Figure Q3a...
QUESTION 1 A semi-crystalline nylon with a degree of crystallinity of 25% has a density of 1.5 g/cm^3. Nylon has a crystalline density of 1.8 g/cm^3. What is its amorphous density in grams per centi...
QUESTION 1 A semi-crystalline nylon with a degree of crystallinity of 25% has a density of 1.5 g/cm^3. Nylon has a crystalline density of 1.8 g/cm^3. What is its amorphous density in grams per centimeters cubed? 1 points QUESTION 2 Which defect is NOT common between metals and polymers? tie molecules vacancies screw dislocations interstitial defects 0.5 points QUESTION 3 Which one is not a characteristic of a plastic polymer? a. Low stress but very large strains b. Tensile strength...
Problem 3 Statically Indeterminate Axially Loaded Members (25pts) The assembly shown consists of rigid bar ABC, two fiber-reinforced plastic (FRP) rods (1) and (3), and FRP post (2). The modulus of elasticity for the FRP is E = 18 GPa. Determine the vertical deflection of joint D relative to its initial position after the 30 kN load is applied. 2.4 m 1.8 m Rigid bar | B |(2) (3) || 3.0 m 3.6 m A = 500 mm? Az= 500...
A uniformly-distributed load wis supported by a structure consisting of rigid bar BDF and three rods. Rods (1) and (2) are 17-mm-diameter stainless steel rods that have an elastic modulus of E = 199 GPa. Rod (3) is a 23-mm-diameter bronze rod that has an elastic modulus of E = 101 GPa. Use a = 1.5 m and L = 3.1 m. For a load magnitude of w = 36 kN/m, calculate (a) the normal stress in each rod. (b)...
A 3 m rigid bar AB is supported with a vertical translational spring at A and a pin at B The bar is subjected to a linearly varying distributed load with maximum intensity g Calculate the vertical deformation of the spring if the spring constant is 700 kN/m. (ans: 21.43 mm) 2. A steel cable with a nominal diameter of 25 mm is used in a construction yard to lift a bridge section weighing 38 kN. The cable has an...
Chapter 3, Reserve Problem 122 The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 × 10-mm/mm/°C]. The cross-sectional area of bar (1) is A1 = 236 mm2 and the cross- sectional area of bar (2) is Az = 389 mm2. After load P has been applied and the temperature of the entire assembly has increased by 26°C, the total strain in bar...
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 x 10-6 mm/mm/°C). The cross-sectional area of bar (1) is A1 = 226 mm- and the cross-sectional area of bar (2) is Az = 362 mm. After load P has been applied and the temperature of the entire assembly has increased by 22°C, the total strain in bar (2) is measured as 1020...
1. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. What is the Poisson's Ratio of this material? 2. A tensile force of 100 kN is applied on a 0.02 m diameter 2 m length rod. After applying the load, the diameter of the rod decreases to 0.01998 m and the length...
The three-bar truss ABC shown in the figure has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm and modulus of elasticity E = 200 GPa. A load P acts horizontally to the right at joint C. (a) If P= 500 kN, what is the horizontal displacement of joint B? (b) What is the maximum permissible load Pox if the displacement of joint B is limited to 2.5mm? 45 45°...
practice exam for mechanic of material
Problem #3: The rigid be m The rigid beam ACE is u sed the suspender bars. Bars AB der hars Bars AB and EF are made of aluminum and har CD is made of steel. Each barha and bar CD is made of steel Fach har has a cross-sectional area of 900 mm, Ex - 200 GPa, E-70 GPa P-20 KN. al 2 m 5 -15 Fox 190 0 3 FAQ +15 Foc 390...
3- (SKMMIH3/SME2113) from plastic having modulus of elasticity, E-4.0GPa a) Bar ABCD shown in Figure Q3a is made The bar consists of three segments, AB, BC, and CD. Segment AB is hollow and segments BC and CD are solids If the shortening (contraction) of bar ABCD is limited to 4.0 mm, determine the maximum allowable force P to be applied at C. (8 marks) 90 mm ΟΙ 00 mm 1080 min PL 500 mm 250 mm 250 mm Figure Q3a...
Most questions answered within 3 hours.
-
What is the % w/v when 80 mL of a 2.0% solution is mixed with 50...
asked 2 minutes ago -
How can I solve the following using a TI83
Claim: Most adults would erase all of...
asked 14 minutes ago -
Analysis of 3-ethyl-3-buten-2-ol gave C, 72.13%; H, 11.92%.
Calculate the percent deviation of these results from...
asked 11 minutes ago -
Which VALS segment is most likely to have a top of the line
brand new (2015)...
asked 15 minutes ago -
Write a program to score the paper-rock-scissor game. Each of
two users types in either P,R...
asked 35 minutes ago -
Calculate the equillibrium constent K for a redox reaction that
has E°cell = -.98 V at...
asked 47 minutes ago -
A concave spherical mirror has a radius of curvature of
magnitude 19.6 cm.
(a) Find the...
asked 49 minutes ago -
3. draw a diagram of the magnetic field:
a. around a long straight wire with a...
asked 48 minutes ago -
If you titrated 30.0 mL of 0.1 M HCl with 0.1 M NaOH, indicate
the approximate...
asked 56 minutes ago -
NADH passes electrons into the electron transport chain. List
the carriers that would receive the electrons,...
asked 1 hour ago -
A cylindrical cable with a resistivity of 1.6x10-8 Ω·m and cross
sectional area of 3x10-5 m^2...
asked 1 hour ago -
True or False.
A consumer with convex preferences who is indifferent between
the bundles (5,2) and...
asked 1 hour ago