2. A h elical compression spring is made of 302 stainless steel wire. The outside coil...
2. A helical compression spring is made from No. 8 steel wire and is to carry a 100 lb static load at a deflection of 1 inch. The outside coil diameter of the spring is 0.972 inches. The spring ends are squared. Assume the torsional yield strength of the wire is 80000 psi, and the shear modulus is 11.4 Mpsi, determine (a) The static load corresponding to the yield strength. (b) The deflection that would be caused by the load...
Design a compression spring with an outside diameter of 11.00 inches from round type 302 stainless-steel wire to operate a plate dispenser in a cafeteria. When fully loaded, the spring is to be compressed 45 inches below the stop under a load of 80 lb, and when empty the spring should exert a force of 0.50 lb against the stop. The ends of the spring are closed. Specify the wire diameter, the number of active turns, the total number of...
QUESTION 1 A compression coil spring made of an alloy steel is having the following specifications:- Mean diameter of coil = 50 mm; Wire diameter = 5 mm; Number of active coils = 20; If the spring is subjected to an axial load of 164 N. Calculate the maximum shear stress (Neglect the curvature effect) to which the spring material is subjected. (units of MPa).
1) [60 pts] Helical Compression Spring A helical compression spring is wound using music wire of diameter, d, 2.64 mm. The spring has an outside diameter, OD, of 33 mm with plain ground ends and 14 coils. a) Estimate the spring rate. The spring rate is N/mm. b) What is the force needed to compress this spring to closure assuming that the spring will reach its shear strength at its solid length? The force needed to compress this spring to...
Solves spring design problems. 2. A compression coil spring can deform 0.4 mm when subjected to 1 kgf. The coil diameter is 60 mm. If the maximum compressive spring force of 200 kgf is required, determine the maximum shear stress and number of effective turns of the spring. The spring index is 7.0 and the shear modulus of the spring material is 0.8 x 10 kgf/mm2. (16점) 2. A compression coil spring can deform 0.4 mm when subjected to 1...
15. The free end of a torsional spring deflects through 90° when subjected to a torque of 4 N-m. The spring index is 6. Determine the coil wire diameter and number of turns with the following data: Modulus of rigidity 80 GPa ; Modulus of elasticity 200 GPa; Allowable stress = 500 MPa. 15. The free end of a torsional spring deflects through 90° when subjected to a torque of 4 N-m. The spring index is 6. Determine the coil...
Problem: A helical compression spring is made with music wire with wire diameter of 5 mm, mean coil diameter of 51 mm, a total of 12 coils, a free length of 127 mm, with squared ends. (a) Find the solid length. (b) Find the force necessary to deflect the spring to its solid length.
Design a helical compression spring subjected to a varying axial force of 1000 N to 2000 N, is made of circular steel wire. Over this force range, the deflection of spring should be approximately 5 mm. Consider spring index = 5, for the spring that has square and ground ends. The spring is made of patented and cold drawn steel wire of grade 1 with A and m = 1753 and 0.182 respectively. The permissible shear stress for the spring...
3 points A coil spring 5.5 cm in outside diameter made of 5 mm wire is to support a mass of 35 kg What is the stress in the wire? O a. 467 MPa Ob. 243 MPa OC 400 MPa O d. 285 MPa O e. 367 MPa
Design a helical torsion spring for severe service using stainless steel wire, ASTM A313. type 302, to exert a torque of 12.0 Ib in after a deflection of 270° from the free condition. The outside diameter of the coil should be no more than 1.250 in. Specify the diameter of a rod on which to mount the spring.