PLEASE ANSWER QUESTIONS 8-10
PLEASE ANSWER # 8-10!!!!
PLEASE ANSWER QUESTIONS 8-10 PLEASE ANSWER # 8-10!!!! Your goal for this experiment is to design...
5. For today's experiment, you will be performing the first step of your multistep synthesis to make trans- 1,2-cyclohexanol from hexanol. You will be using distillation to separate the product of the first step in the synthesis. (see the procedure below for diagrams and photos of what distillation setup looks like. Check the boiling points provided in the chemical table for starting material and product. Which compound boils at a lower boiling point? Explain briefly based on boiling point differences...
Experiment Questions What is an epoxide and how is it useful with respect to synthesis design? • What are typical reagents used for epoxidation? • What is the mechanism for epoxidation? Must stereospecificity be considered? Experiment Techniques • Use of sodium bisulfite wash to remove excess peroxy acid from reaction mixture. Introduction By now you are well aware that the product of previous experiment (reaction of cyclohexanol and acid) is an alkene. You should also be storing key reactions of...
Please help with the pre- lab exercise and questions 10 and 11 Experiment 19 Heat of Combustion: Magnesium 18, you learned about the additivity of reaction beats as you confirmed Hess's Law, In this experiment, you will use this principle as you determine a heat of reaction that would be difficult to obtain by direct measurement-the heat of combustion of magnesium ribbon. The reaction is represented by the equation This equation can be obtained by combining equations (1). (2), and...
3. (4 pts) The key step involves a base pulling off one of the benzylic hydrogens in the starting material. Given that the pk of an alkane hydrogen is > 50 and the pk, of a benzylic hydrogen is < 40, explain why potassium hydroxide can be used instead of sodium amide to synthesize 1,2-diphenylethyne from a vicinal dibromide. 4. (4 pts) Fill in the following table showing amounts to use and theoretical yield. Show your work. Product 1,2-diphenylethyne Amounts...
Fill in the table and answer the questions below Name Pre-lab Questions (10 Marks) 1. Fill the table below: Materials Acetic anhydride H:SO, Salicylic acid Amount 12mL 0.25 mL 3mL Measured Molecular weight (g/mol) Moles 2. Identify the limiting reagent in this reaction? 3. Calculate the theoretical mass yield of Aspirin product? Show your work for full credit. [4] 4. What is the literature melting point of Aspirin (acetyl salicylic acid)?
EXPERIMENT 8: Synthesis of Aquapentaammine-Cobalt (II) Nitrate, [Co(NH)sH2O1(NO)s Pre-Lab Questions: The complex salt [Cu(NH3)4][SO,1- H,O can be prepared by direct combination of its constituents: Cu +4 NH,+SO+ H2O [Cu(NH)JSO. H;O In an aqueous reaction solution contained 1.0 g CuCl, 2H2O, 1.0 mL 14 M NHs, and 1.0 g NazSO, what would be the maximum theoretical vield (in grams) of product? To what percent yield would 0.42 g of product correspond? Your yield of crude product is 1.8 g and you...
I did an experiment where I synthesized 2-phenyl-2-propanol using the grignard reaction. please help me answer these lab questions Reagents Moles of Reagent 0.00142 moles (0.224 g)bromobenzene 0.00712 mol (0.173 g) 2 mL of THF (n/a moles) tetrahydrofuran 0.00142 mol (0.083g, 0.11mL) acetone, HPLC grade, anh Reagent Name FW 157.75 24.31 n/a 58 Comments Mg powder grind before using must be anhydrous must be anhydrous Pre-Lab Assignment: 1. Determine the volume (mL) of bromobenzene needed for the experiment. Obtain the...
i need help please Pre-Lab Study Questions Synthesis of Acetaminophen Synthesis of Acetaminophen 1. Maak Mass of watch ples 4. Mass of watch glass + pure acetaminophen Melting point of the pure cetaminophen 6. Mass of paminophenol 7. Mass of pure aminophen & Theoretical yield of etaminophen Percent yield Show callao Photos LTE 11:57 PM 1 31%O b. What is the percent yield of acetaminophen for the reaction? Synthesis of Acetaminophen Synthesis of Acetaminophen 1. Mass of flask 2. Mass...
4. Turn-in Pre-Lab Assignment - Experiment and Objectives (10 pts) You MUST turn this paper in to your TA at the start of the LAB SESSION! YOUR Name: Lab room: Partner Name: Lab time: TA Name: Hood #: Give brief, 1-2 sentence responses to the following questions 1 (3 pts). What is the solvent, what is the reagent and what is the reactant you will use in your synthesis of acetaminophen? Solvent = Reagent = Reactant 2 (1 pt). What...
Question 2 and possibly 3 please. Pre-lab Questions: 1. Refer to the Safety Data Sheets to find the molecular weights and hazards of all chemicals used in today's experiment, including the product, and record this information on your synthesis sheet. *Note Safety Data Sheets can be found on myDCC under “Safety Data Sheet E-Library”. 2. Refer to the above equation for the preparation of 2-methyl-2-butene, calculate the following: a. number of moles of 2-methyl-2-butanol in 5 grams b. number of...