Why the absorbance increase or decrease when a sample is analyzed and measured throughout the flame height?
The answer for this question can be answered if we study the flame profile first
The temperature of the flame is not the same all the length of the flame
The absorbance that we get in this experiment is due to the excited atoms that ionise in the flame
It changes as we down or up the flame
So when a sample is analysed at different flame heights the amount of temperature it gets is different and hence the amount of excited ions which further shows absorbance also changes
And thats the reason the absorbance changes at different heights of the flame
I hope this helps. If you have any query or want more detailed explanation, feel free to ask in the comments section below.
Why the absorbance increase or decrease when a sample is analyzed and measured throughout the flame...
If a sample is analyzed in a 10-cm cell (cuvet), the absorbance will be 10 times greater than the absorbance in a 1 cm cell. Will the absorbance of the reagent-blank also be increased by a factor of 10?
3. A 2.50x10-M solution of a dye has an absorbance of 0.520 when measured in a 1.00 cm cell at 625 nm. Calculate the %Transmittance of the solution. Will the %Transmittance increase or decrease if the concentration of the dye is increased. CamScanner
1.When a tsunami wave approaches the coast : - Does speed increase or decrease ? - Does height increase or decrease ? - Does wavelength increase or decrease ? Explain why.
In this experiment we injected the sample to be analyzed by Gas Chromatograph equipped with an FID (Flame Ionization Detector). The detector ionizes the sample as it reaches it, and the peak is proportional to the number of ions with a live flame. A chemist performed a distillation of methanol and water and wanted to analyze the results using the same GC instrument with FID. Could he use a similar procedure to analyze the results of his experiment? Explain why...
Part C The absorbance of a cationieron) sample solution was measured in a spectrophotometer, but the instrument returned an error because the absorbance was too high. The sample was then diluted by using a pipette to take 100.0 L of the sample and injecting it into a cuvette already containing 2.00 mL of water total volume is 200 ml + 100.0 L). The absorbance value of the diluted solution corresponded to a concentration of 7.84x10-6 M. What was the concentration...
4. The measured absorbance of a sample in a 1.00 cm cuvette is 0.544. If the concentration is 1.4 x 10-M, what is the molar absorptivity for this species?
1 Why does absorbance decrease when you add DCPIP to cholorplast and use light ? 2 Where would you find LHCII ? 3 What will happen if you put the gel against the positive pole and the membrane against ghe negative pole? 4 Why is immunoblotting better than using Commassie Blue? 5 If an herbecide was used and only co2 was generated and ATP was not generated, what was the mode of action of herbecide?
Part C The absorbance of a cationic iron(II) sample solution was measured in a spectrophotometer, but the instrument returned an error because the absorbance was too high. The sample was then diluted by using a pipette to take 100.0 μL of the sample and injecting it into a cuvette already containing 2.00 mL of water (total volume is 2.00 mL + 100.0 μL). The absorbance value of the diluted solution corresponded to a concentration of 6.70×10−6 M . What was...
2. A calibration curve has a least-squares equation Pe=1.48(ppm Ca2+). A neat water sample was analyzed by flame photometry. The Emitted Power was measured to be 14.4. What is the hardness of the water sample in ppm CaCO3? Report answer to one decimal places. Do not enter units.
Questions 13–15 concern the following analysis: A serum sample is analyzed for potassium by flame emission spectrometry using the method of standard additions. Two 0.500-mL aliquots of serum are added to 5.00-ml portions of water. To one portion is added 20.0 uL of 0.0750 M KCI solution. The net emission signals in arbitrary units are 23.2 and 68.6? 13. What is the magnitude of the emission signal produced by the standard? Final answer: 14. How many millimoles potassium are present...