Given that:
Air at 1 atm
Temperature t = 60 deg F
Cross sectional area = 1 ft * 1 ft
Commercial steel at a rate of 1200 cfm
please solve chi. Iduulu 1 8_48E Air at 1 atm and 60°F is flowing through a...
Q1: Heated air at 1 atm, 100F, and 23% relative humidity is to be transported in a 490 ft long circular plastic duct at a rate of 740 cfm (ft 3 /min). If the head loss in the duct is not to MEC_AMO_TEM_034_01 Page 1 of 8 Design of Thermal System (MECH 0009) - Spring-2020 -Assignment 2- A&B - QP exceed 790 in. of air, determine the minimum diameter of the duct. (Hint: initial guess value for the diameter is...
Prob#1 mainstream A 0.5-m-square duct contains air flowing from Um = 1.5 m/s entering the duct at 1 atm and 25 C, as shown in Figure below. Applying the appropriate boundary layer concept, calculate the (a) The average velocity at 2 m in the duct. (b) Pressure drop along the duct, in Pa/m unit. 0.5-m-square duct Boundary layers U mainstream U -2 m
I hope that the hand writing for the Ans to be clear The Ans should be in details Heated air at 1 atm, 100 ° F, and 23% relative humidity is to be transported in a 490 ft long circular plastic duct at a rate of 740 cfm (ft 3 /min). If the head loss in the duct is not to À A 11 - Arial (com exceed 790 in. of air, determine the minimum diameter of the duct. (Hint:...
16. (10p) Air in a heating system is distributed through a rectangular duct (0.2m x 0.3 m) made of commercial steel (average roughness height = 0.000045 m) at a rate of 0.5 m/s. Calculate the pressure drop and head loss in the 40 m length part of this duct and the needed pumping power to overcome the losses. Pair 1.169 kg/m3, Hair = 1.918x10-5kg/ms
Conditioned air at 1 atm and approximately 12C is to be transported via a circular duct at 0.3 m^3/s. The distance between the air conditioner and the space to be conditioned is 50 m. The fan capacity limits the head loss to a maximum of 300 m of air. Find the minimum diameter of the duct. Hint: Guess a diameter, from which you can deduce the average velocity. Then, based on the Reynolds number, and the roughness (based on the...
Air in a large storage tank is 91 psia and 60°F is flowing isentropically through the duct shown below to the atmosphere. The pressure, psia, in the duct throat is most nearly Po = 91 psia مها : 7 Pater Hint: Assume the flow is choked, then the fluid speed in the throat is equal to the speed of sound and the pressure in the throat is equal to the critical pressure p
Air at 30oC and 5 bars is flowing inside a 1/2in.schedule 40 steel pipe if the flow is at 4.0 ft3/min at standard temperature and pressure(0oC and 1atm) is the flow likely to be laminar or turbulent?
Air enters a 10-m-long section of a rectangular duct of cross section 15 cm X 20 cm made of commercial steel at an average velocity of 7 m/s.(p = 1.145kg/m3 ,μ = 1.895x10-5kg/ms) and e=0.000045 m). For this pipe determine (a)the Reynolds number and decide weather the flow is laminar or turbulent (b) the head loss, (c) the pressure drop, and (d) the pumping power requirement to overcome this pressure drop.
please solve 25 in detail 24. Water is flowing through a 7500-m long, 0.90-m diameter commercial steel pipe in its best condition. At the upstream end of the pipe, the elevation head is 83.5 m and the pressure head is 12.3m. At the downstream end of the pipe, the elevation head is 0 m and the pressure head is 88.7 m. Use the Hazen Williams equation to solve for the flow rate in this pipe. Answer: Q = 0.73 m2/s....
Please solve a,b,c,d,e,f 1) A water fountain is to be installed at a remote location by attaching a cast iron pipe directly to a water main through which water is flowing. The entrance to the pipe is sharp-edged 15m (K-0.5), and the 15m long piping system involves three 90 bends without vanes (K1.1), a fully open gate valve (K.-0.2), and a fully open angle valve (K-5). If the diameter of the pipe is 2 em and the system is to...