(1 ) Problem 2: A 20° full-depth steel (milled profile) spur pinion has a diametral pitch...
6) [20 pts) Bending Stress in a Gear A steel spur pinion has a pitch of 6 teeth/in, 22 full-depth teeth with a cut profile, and a 20° pressure angle. The pinion runs at a speed of 1280 rev/min and transmits 15 hp to a 60-tooth gear. If the face width is 2 in., estimate the bending stress. Take the value of Lewis form factor, Y, from the table 14-2. The bending stress is kpsi.
Question #5 (20 pts) A pinion has 18 teeth and a diametral pitch of 9 teeth/in, a face width of 1,5 in sa pressure angle of 20° with full-depth teeth. The spur gear is made by the milling or emin required to transmit at least 11 hp horsepower with a corresponding speed and moderate applications. Which material is the best choice for the spu ones in Table 5 considering the maximum allowable bending stres (factor of safety, nd-2.5)? U quations...
3. A commercial enclosed gear drive consists of a 20 spur pinion having 16 teeth driving a 48-tooth gear. The pinion speed is 300 rev/min, the gear face width 2 in., and the diametral pitch 6 teeth/in. The gears are grade t steel, through-hardened at 200 Brinell, made to No. 6 quality standards, uncrowned, and are to be accurately and ngid mounted Assume a lion life ofi will transmitareliability of90%(KR 0.85), and use YN 1.355N 01:8 and Z 1. used...
Please help. Thx Part 2 (50 pts) A single-reduction spur gear system is as shown. The pinion "P" drives gear "G. Pinion"Pis driven at 1800 rpm with 1.5 hp Pinion "P" has a pitch diameter of 2 inches, and has 20 teeth. The gear "Ghas 120 teeth. All teeth have a pressure angle of 20, full-depth, hobbed profile, and a face width of 0.5 inches. All materials are steel. Determine: A) Minimum number of pinion teeth: Np,min This shows that...
Question 28 65 pts Aspur gear has a diametral pitch of 6 teethin, 20 teeth 20 degrees pressure angle, full-depth and milled profile teeth with a face width of 1.5 in. The pitch line velocity is 750 ft/min. The gear is made of a material AISI 1040 HR steel What is the maximum allowable tangential load (b) that the Eear teeth can sustain based on the tooth bending stress criteria (provide answer to one decimal place?
A helical gear has a normal diametral pitch of 24, a normal pressure angle of 14 ½ o, 72 teeth, a face width of 0.25 in and helix angle of 45° The power comes from an electric motor, and the drive is to winch that will experience moderate shock. (a) If the gear transmits 0.50 HP at a speed of 3450 RPM, what would be the tangential force? (b) If the gear operates with a pinion having 16 teeth, what...
Student Name (Print): Q3. (10 points) A steel spur pinion has 18 teeth cut on the 20° full-depth system and a module of 1.25 mm. This pinion will carry 0.6 kW at 1500 rev/min. Determine the pitch line velocity, Lewis Form Factor and the dynamic factor to use when calculating the bending stress. (Note: Do not calculate the bending stress.)
7) [30 pts] Factor of Safety for Contact Stress A steel spur pinion has 16 teeth cut on the 20 full-depth system with a module of 8 mm and a face width of 90 mm. The pinion rotates at 150 rev/min and transmits 3 kW to the mating steel gear. This pinion is to mesh with a steel gear with a gear ratio of 4:1. The Brinell hardness of the teeth is 200, and the tangential load transmitted by the...
9. AGMA Shigley 5th Ed. 14-27 A 17-tooth 20°-pressure angle spur pinion rotates at 1800 rev/min and transmits 4 hp to a 52-tooth gear. The diametral pitch is 10, the face width is 1.25 in, the quality standard is No. 6, and the mounting is with exceptional rigidity. The pinion is steel, hardened to Brinell 240, and the gear is of No. 30 cast iron. Find the factor of safety based on surface fatigue strength if the life is to...
A speed reducer has 20° full-depth teeth with a diametral pitch of 4 teeth/in, a face width of 3.25 inches, and with the pinion having 22 teeth and the gear having 60 teeth. The pinion is driven by a 40 HP motor rotating with a shaft speed of 1145 rpm. The pinion is designed to last for 5 years operating around the clock. The gears are manufactured using 4340 through-hardened grade 1 steel, both heat treated to 250 HB using...